1) water clear epoxy doming resin
2) non-toxic and non-volatile content
3) accept sample order
FEATURES
Flexible Ultra Clear Two-part Decorative Epoxy Doming Resin APS-EP100S A/B
APS-EP100F A/B is two-part epoxy doming curing in room temperature. Will not harden upon aging and does not leave a sticky surface. It is widely used on appliances, automobiles, computers, stereo equipment and such.
PERFORMANCE
Testing Item
Testing Method
EP100S A
EP100S B
Appearance
Visual
Clear
Clear
Density
25°C g/cm3
1.0~1.1
1.0~1.1
Viscosity
25°C mpa·s
4500~5000
500~800
Storage Time
Room temperature
ventilated
One year
One year
TECHNOLOGY
Item
Unit
EP100S A/B
Mixing Ratio
Weight Ratio
1:1
Up Time
25°C/min
60
Surface Drying Time
25°C/h
8~10h
Full Dry Time
25°C/h
15~20h
1. Keep the surface dry and cleaning;
2. Take the glue as ratio, and keep it accurate; Please stir the glue fully after mixed;
3. Use the mixed glue promptly;
4. Please keep the environments cleaning.
FEATURES AFTER CURED
Item
Unit
EP100S A/B
Hardness
25°C,Shore-D
75
Compression strength
kg/mm
2
>25
Bending strength
kg/mm
2
>10
Impact strength
kg/mm2/cm2
>6
Insulating srength
25°C,kV/mm
>22
Dielectric constant
25°C,1MHZ
4.2±0.1
Compressive strength
kg/mm
2
70
Shear strength
(Steel/Steel)
kg/mm
2
18
Tensile strength
(Steel/Steel)
kg/mm
2
30
STORAGE AND NOTE
1. This products are not dangerous goods, so it can be stored as usual goods.
2. Please clean with cleaner if there is some glue bonding to your skin, and then go to hospital.
PACKAGE
20kg/drum; 200kg/drum. Custom made.
Saturday, September 17, 2011
Epoxy glue ( Rhinestone glue)
our epoxy glue:
1. little or no shrink.
2.easy to use ,mix ratio is 1:1
3.perfect for Rhinestone etc.
4.high bond strength.
Product Description
:
KS-BOND® epoxy glue 919 is two component ,clear epoxy adhesive. They are water ,impact resistant, and excellent bond strength ,bonding metal ,glass ,ceramic , stone ,hard plastic ,FRP ,wood etc .Especially recommended for jewelry industry to color and transparency of the higher requirement of materials such as rhinestone.
Features:
1. little or no shrink
2.easy to use ,mix ratio is 1:1
3.perfect for Rhinestone etc.
4.high bond strength
Properties:
item
Base
hardener
Appearance
Colorless to buff transparent liquid
Colorless to buff transparent liquid
Component
Epoxy resin
Modified Amine
Viscosity(mpa.s/25 )
8000-20000
10000-30000
Solid content
100
100
Mix ratio (weight)
1
1
Work time (25)
1hour
Initial curing time(25)
6hours
Initial curing time(60)
2hours
Total curing time
25*7days
Total curing time
60*1day
Bond strength(between iron and iron)
110kg/cm2(25*7days)
Directions for use:
1. Clean the surfaces to be bonded firstly.
2. Mix ratio by weight :part A: part B=1:1
3. Apply evenly to all surfaces to be bonded and put them together to cure at room temperature or heating. e
4. It is ok when cure totally.
Caution:
1. By weight ,the mix ratio is 1:1.
2. Stir evenly and use it up in work time .
3. After mixing together ,glue will get curing in 50 minutes.
First aid:
1. If skin contacted, flush with water and soap.
2. Keep out of the reach of children.
3. If swallowed ,please get medical attention immediately.
Shelf Life :
18 months
1. little or no shrink.
2.easy to use ,mix ratio is 1:1
3.perfect for Rhinestone etc.
4.high bond strength.
Product Description
:
KS-BOND® epoxy glue 919 is two component ,clear epoxy adhesive. They are water ,impact resistant, and excellent bond strength ,bonding metal ,glass ,ceramic , stone ,hard plastic ,FRP ,wood etc .Especially recommended for jewelry industry to color and transparency of the higher requirement of materials such as rhinestone.
Features:
1. little or no shrink
2.easy to use ,mix ratio is 1:1
3.perfect for Rhinestone etc.
4.high bond strength
Properties:
item
Base
hardener
Appearance
Colorless to buff transparent liquid
Colorless to buff transparent liquid
Component
Epoxy resin
Modified Amine
Viscosity(mpa.s/25 )
8000-20000
10000-30000
Solid content
100
100
Mix ratio (weight)
1
1
Work time (25)
1hour
Initial curing time(25)
6hours
Initial curing time(60)
2hours
Total curing time
25*7days
Total curing time
60*1day
Bond strength(between iron and iron)
110kg/cm2(25*7days)
Directions for use:
1. Clean the surfaces to be bonded firstly.
2. Mix ratio by weight :part A: part B=1:1
3. Apply evenly to all surfaces to be bonded and put them together to cure at room temperature or heating. e
4. It is ok when cure totally.
Caution:
1. By weight ,the mix ratio is 1:1.
2. Stir evenly and use it up in work time .
3. After mixing together ,glue will get curing in 50 minutes.
First aid:
1. If skin contacted, flush with water and soap.
2. Keep out of the reach of children.
3. If swallowed ,please get medical attention immediately.
Shelf Life :
18 months
1pc/card instant bond
item name:super glue
packing: 1pc/card, 12card/ gift box, 12 box/carton
delivert time: 30 days
meas:28*23*36cm/144card
Super Glue
suits for plastic,rubber,metal,leather,ceramic,wood and so on.
our production can made under your trade mark.
Item name
super glue
Item no.
JYA-001B
application
For WOOD,RUBBER,PLASTIC,METAL PAPER,AND LEATHER
Weight
1-3g
package
1pc/card, 12card/ gift box,12box/carton
measurement
28*23*36cm
OEM
Available
Appearance
liquid,clear
Shelf life
12 months
Certification
SGS
Application
:
Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure.
Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis-sue paper. Keep out of reach of children, in cool dry place
Warning:
Keep out of reach of children:
Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm warter and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor.
Bond for home uses
:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
packing: 1pc/card, 12card/ gift box, 12 box/carton
delivert time: 30 days
meas:28*23*36cm/144card
Super Glue
suits for plastic,rubber,metal,leather,ceramic,wood and so on.
our production can made under your trade mark.
Item name
super glue
Item no.
JYA-001B
application
For WOOD,RUBBER,PLASTIC,METAL PAPER,AND LEATHER
Weight
1-3g
package
1pc/card, 12card/ gift box,12box/carton
measurement
28*23*36cm
OEM
Available
Appearance
liquid,clear
Shelf life
12 months
Certification
SGS
Application
:
Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure.
Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis-sue paper. Keep out of reach of children, in cool dry place
Warning:
Keep out of reach of children:
Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm warter and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor.
Bond for home uses
:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
Epoxy glue for metal
The adhesive is especially suitable for stainless steel and rubber.
Introduction:
CW-J-101 Epoxy Adhesive is fit on Non-Ferrous Metal and Black Metal bind
with Non-Metal Material, especially on Stainless bind with Rubber .
Product Features:
High Bonding Strength, Simple Use of Technology, Easy to Operate, Fit for Industrial Production.
Product Specification:
1. Appearance:
Group A: Yellow Viscous Liquid
Group B: Reddish-Brown Liquid
2. Use Technology:
a: Blending Ratio : 100 : 50 (Weight Ratio)
b: Curing Condition: 60°C 2 HOUR
Attentions:
1. If in winter, It’s easy to operate that Pre-heating Group A and B separately to 40°C first,then blend them.
2. Operating has to be strictly according the blend ratio (weight ratio),
weighting accurately, well stirred.
3. A,B material guarantee period is 6 month, should store in the shady and dry place. After uncap using, unfinished material please seal immediately after using.
4. Please don’t touch the skin and wear the gloves to protect the skin.
5. If contacts the skin, please directly wipe out with the soap water, if contacts the eyes, please flushing by massive water, and please go to see the doctor if needed.
Heath and Safety:
The product is solvent-free epoxy, nonpoisonous, non-flammable, if the
glues splash please to use cloth dips or adsorbs with the sand to eliminate.
Introduction:
CW-J-101 Epoxy Adhesive is fit on Non-Ferrous Metal and Black Metal bind
with Non-Metal Material, especially on Stainless bind with Rubber .
Product Features:
High Bonding Strength, Simple Use of Technology, Easy to Operate, Fit for Industrial Production.
Product Specification:
1. Appearance:
Group A: Yellow Viscous Liquid
Group B: Reddish-Brown Liquid
2. Use Technology:
a: Blending Ratio : 100 : 50 (Weight Ratio)
b: Curing Condition: 60°C 2 HOUR
Attentions:
1. If in winter, It’s easy to operate that Pre-heating Group A and B separately to 40°C first,then blend them.
2. Operating has to be strictly according the blend ratio (weight ratio),
weighting accurately, well stirred.
3. A,B material guarantee period is 6 month, should store in the shady and dry place. After uncap using, unfinished material please seal immediately after using.
4. Please don’t touch the skin and wear the gloves to protect the skin.
5. If contacts the skin, please directly wipe out with the soap water, if contacts the eyes, please flushing by massive water, and please go to see the doctor if needed.
Heath and Safety:
The product is solvent-free epoxy, nonpoisonous, non-flammable, if the
glues splash please to use cloth dips or adsorbs with the sand to eliminate.
Epoxy glue gun
1) competitive price epoxy glue gun
2) easy to operate
3) accept sample order
4) match with two parts epoxy/silicone
Epoxy glue gun
Caution
(1) Note the time, when the glue becomes curing and hot in the mixing tube, you should replace the mixing tube.
(2) Please don’t use excessive force to pull downward the C buckle bit when you want to install or replace the adhesive.
2) easy to operate
3) accept sample order
4) match with two parts epoxy/silicone
Epoxy glue gun
Caution
(1) Note the time, when the glue becomes curing and hot in the mixing tube, you should replace the mixing tube.
(2) Please don’t use excessive force to pull downward the C buckle bit when you want to install or replace the adhesive.
Epoxy glue,AB GLUE,Adhesive glue,Epoxy Adhesives
AB glue is the adhesive for households and School Supplies
AB glue
Item number: TY-B5
Specification: 28g
Measurement (cm): 48*30*49
It can stick materials of the same and different kinds including metals, plastics
and wood, which are widely used for making or repairing vehicles, channels,
furniture, lighting, signboard, toys, daily articles and pipeline in chemical
industry.
AB glue
Item number: TY-B5
Specification: 28g
Measurement (cm): 48*30*49
It can stick materials of the same and different kinds including metals, plastics
and wood, which are widely used for making or repairing vehicles, channels,
furniture, lighting, signboard, toys, daily articles and pipeline in chemical
industry.
Epoxy laminating resin
Epoxy laminating resin accepts sample order
1) good bonding
2) Excellent viscosity
3) waterproof
4) insulativity
Epoxy laminating resin
INTRODUCTION
EP106 AB is a two part potting and encapsulating compound. Typical applications include encapsulation, potting and assembly of electronic and magnetic components, such as capacitors, transformers, terminals, industrial magnets, small and large magnetic assemblies, metal detectors, metal separators, magnetic printing cylinders, magnetic holders, insulators, junction boxes, switches, circuit boards. General-purpose casting and bonding for structural and dielectric applications.
PROPERTIES
EP106A
EP106B
Color
Black, white, Clear
Clear amber
Viscosity cps/25°C
10,000~14,000
80~100
Specific gravity
15~1.6
1.0~1.1
APPLICATION CONDITIONS
Mix Ration (weight)
EP106A:EP-06B=5:1
Mix Viscosity cps/25
°C
2000~3000
Pot Life (at 25
°C
)
40min (After Mixing)
Cure
25°C×6~8h or 60°C×1h
CURED PROPERTIES
Hardness (Shore D)
88
Volume resistivity (ohm-cm)
>10
15
Surface resistivity (ohm)
>10
14
Dielectric constant (KHZ)
4.2±0.1
Compressive strength (kg/mm
2
)
>25
Bending strength (kg/mm
2
)
>10
Impact strength(kg/mm
2
/cm
2
)
>6
DIRECTIONS FOR USE
1)
Complete cleaning of the substrates should be performed to remove contamination such as oxide layers, dust, moisture, salt and oils which can cause poor adhesion or corrosion in a bonded part.
2) Accurately weigh resin and hardener into a clean container in the recommended ratio. Weighing apparatus having an accuracy in proportion to the amounts being weighed should be used.
3) Don't touch your skin and eyes, if touch skin, washing with soap water; if touch eyes, washing with water, then get to hospital immediately.
4) Material removed from containers may be contaminated during use. Do not return product to the original container.
STORAGE
Store in original, tightly covered containers in clean, dry areas. Storage information may be indicated on the product container labeling.
Material removed from containers may be contaminated during use. Do not return product to the original container.
PACKING
20Kg/Drum
1) good bonding
2) Excellent viscosity
3) waterproof
4) insulativity
Epoxy laminating resin
INTRODUCTION
EP106 AB is a two part potting and encapsulating compound. Typical applications include encapsulation, potting and assembly of electronic and magnetic components, such as capacitors, transformers, terminals, industrial magnets, small and large magnetic assemblies, metal detectors, metal separators, magnetic printing cylinders, magnetic holders, insulators, junction boxes, switches, circuit boards. General-purpose casting and bonding for structural and dielectric applications.
PROPERTIES
EP106A
EP106B
Color
Black, white, Clear
Clear amber
Viscosity cps/25°C
10,000~14,000
80~100
Specific gravity
15~1.6
1.0~1.1
APPLICATION CONDITIONS
Mix Ration (weight)
EP106A:EP-06B=5:1
Mix Viscosity cps/25
°C
2000~3000
Pot Life (at 25
°C
)
40min (After Mixing)
Cure
25°C×6~8h or 60°C×1h
CURED PROPERTIES
Hardness (Shore D)
88
Volume resistivity (ohm-cm)
>10
15
Surface resistivity (ohm)
>10
14
Dielectric constant (KHZ)
4.2±0.1
Compressive strength (kg/mm
2
)
>25
Bending strength (kg/mm
2
)
>10
Impact strength(kg/mm
2
/cm
2
)
>6
DIRECTIONS FOR USE
1)
Complete cleaning of the substrates should be performed to remove contamination such as oxide layers, dust, moisture, salt and oils which can cause poor adhesion or corrosion in a bonded part.
2) Accurately weigh resin and hardener into a clean container in the recommended ratio. Weighing apparatus having an accuracy in proportion to the amounts being weighed should be used.
3) Don't touch your skin and eyes, if touch skin, washing with soap water; if touch eyes, washing with water, then get to hospital immediately.
4) Material removed from containers may be contaminated during use. Do not return product to the original container.
STORAGE
Store in original, tightly covered containers in clean, dry areas. Storage information may be indicated on the product container labeling.
Material removed from containers may be contaminated during use. Do not return product to the original container.
PACKING
20Kg/Drum
Epoxy marble tile adhesive for Steel Bar Planting
1)Good bonding and strongly permeate
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
Epoxy potting compound ( cures at room temperature)
1.good transparency,
2.heat resistance,
3.cures at room temperature
This is a two-component epoxy resin compound (4:1).
Curing condition (h/°C): 10~12/23
Thermal resisting class: F
It provides an ideal solution for potting elements and components in motors, electric apparatus and electronic products.
Jiaxing Rota-Ropa Insulating Material Co. ,Ltd. is an experienced two component trickle resin varnish manufacturer in China, founded in 1994. In addition to trickle resin, we also produce many other types of insulating varnish, like impregnating resin varnish, air drying varnish, and balancing cement, etc. All our products are SGS and CCC certified and well accepted by customers from the United States, Australia, France, Iran, Algeria, Venezuela, Germany and Russia, and more.
If you are interested in our insulating varnish, pick up your phone and call us now.
2.heat resistance,
3.cures at room temperature
This is a two-component epoxy resin compound (4:1).
Curing condition (h/°C): 10~12/23
Thermal resisting class: F
It provides an ideal solution for potting elements and components in motors, electric apparatus and electronic products.
Jiaxing Rota-Ropa Insulating Material Co. ,Ltd. is an experienced two component trickle resin varnish manufacturer in China, founded in 1994. In addition to trickle resin, we also produce many other types of insulating varnish, like impregnating resin varnish, air drying varnish, and balancing cement, etc. All our products are SGS and CCC certified and well accepted by customers from the United States, Australia, France, Iran, Algeria, Venezuela, Germany and Russia, and more.
If you are interested in our insulating varnish, pick up your phone and call us now.
Epoxy reisn Injection mortar
Construction use planting bar adhesives
XQ-901 Injection Adhesives are compound of modified epoxy resin and nano materials, double component packed. The advantage on plating bar anchoring has been proved by many construction projects,
Features:
• Modified epoxy resin, styrene free, safe and non-toxic;
• High strength and reinforcement, good toughness, similar with pre-cemented;
• Good resistance against aging and heat, no creep under normal temperature;
• Low sensitivity with humidity, steady performance under moist condition;
XQ-901 Injection Adhesives are compound of modified epoxy resin and nano materials, double component packed. The advantage on plating bar anchoring has been proved by many construction projects,
Features:
• Modified epoxy resin, styrene free, safe and non-toxic;
• High strength and reinforcement, good toughness, similar with pre-cemented;
• Good resistance against aging and heat, no creep under normal temperature;
• Low sensitivity with humidity, steady performance under moist condition;
Epoxy resin Chemical Anchor Adhesive
Anchor Adhesive,
Double component, Fast solidity;
Used for concrete, Stones, Metals etc;
Temprature ranged -5 - 45 C.degree;
Double Component Noraml temprature Anchor Adhesive,
Features:
Double component, Fast solidity;
Used for concrete, Stones, Metals etc;
Temprature ranged -5 - 45 C.degree;
High strength and reinforcement, good toughness, similar with pre-cemented;
Fields of Usage:
1. All kinds of steel bar planting and anchor for costruction structure.
2. All kinds of equipment base
3. Anchor support for the roofs and walls of the mine
4. water resource facilities, yard, roadway, bridge
Double component, Fast solidity;
Used for concrete, Stones, Metals etc;
Temprature ranged -5 - 45 C.degree;
Double Component Noraml temprature Anchor Adhesive,
Features:
Double component, Fast solidity;
Used for concrete, Stones, Metals etc;
Temprature ranged -5 - 45 C.degree;
High strength and reinforcement, good toughness, similar with pre-cemented;
Fields of Usage:
1. All kinds of steel bar planting and anchor for costruction structure.
2. All kinds of equipment base
3. Anchor support for the roofs and walls of the mine
4. water resource facilities, yard, roadway, bridge
Epoxy resin Injective glues
1.Bicomponent modified epoxy resin injection anchor adhesive
2.Not contain styrene, non-toxic
3.Good thixotropy
4.Convenie
1.
Product Characteristics
1) Modified epoxy resin, not contain styrene, safe and non-toxic
2) High strength, strong cohesion, good toughness, effect is equivalent to embedded.
3) Aging resistance, good heat-resistant performance, creep does not occur at room temperature.
4) Low moisture sensitivity, long-term load stability in a damp environment.
5) Acid-alkali resistance, good seismic resistance performance, no expansion.
6) Good thixotropy, especially suitable for anchoring the side or top.
7) Binocular straight mixed package, with special glue gun, not need prepare glue manually.
2.
Application
Range
1) The planting of steel bars and bolts in concrete’s frame member.
2) The fixation of drying hanging brackets of curtain walls and stone materials.
3) The reinforcement of building structures and the anchorage of framework.
4) The basic fixation of many equipments.
5) The anchoring connection of steel structures and concrete structures.
6) The engineering reinforcement of railways, public roads, bridges, water conservancy facilities’ reconstruction and extension, etc.
7) The fixation of advertisement boards, tunnel pipe lines, elevated road noise barriers and barricades.
.
Performance indexes
item
index
Colloidal performance
Splitting tensile strength (MPa)
Bending strength (MPa)
Compressive strength (MPa)
≥8.5
≥50
≥60
Adhesion performance
Steel-steel (steel sleeve) tensile anti-shear strength (MPa)
Under the constraint drawing condition, ribbed steel bars and C30, φ25, L=150mm (MPa)
Adhesion strength of concrete C60, φ25, L=125mm (MPa)
≥16
≥11
≥17
Non-volatile matter content (solid content) (%)
≥99.5
Construction technical indexes
rebar diameter(mmm)
10
12
14
16
18
20
22
25
28
30
drill hole diameter(mm)
14
18
20
22
25
28
30
32
35
37
tension desiger(KN)
depth 10d
19.5
27.7
36.2
50.1
61.5
81.1
98.2
125.2
155.3
190.8
depth 15d
24.2
33.1
46.9
61.8
77.7
96.5
116.8
149.3
187.5
236.1
2.Not contain styrene, non-toxic
3.Good thixotropy
4.Convenie
1.
Product Characteristics
1) Modified epoxy resin, not contain styrene, safe and non-toxic
2) High strength, strong cohesion, good toughness, effect is equivalent to embedded.
3) Aging resistance, good heat-resistant performance, creep does not occur at room temperature.
4) Low moisture sensitivity, long-term load stability in a damp environment.
5) Acid-alkali resistance, good seismic resistance performance, no expansion.
6) Good thixotropy, especially suitable for anchoring the side or top.
7) Binocular straight mixed package, with special glue gun, not need prepare glue manually.
2.
Application
Range
1) The planting of steel bars and bolts in concrete’s frame member.
2) The fixation of drying hanging brackets of curtain walls and stone materials.
3) The reinforcement of building structures and the anchorage of framework.
4) The basic fixation of many equipments.
5) The anchoring connection of steel structures and concrete structures.
6) The engineering reinforcement of railways, public roads, bridges, water conservancy facilities’ reconstruction and extension, etc.
7) The fixation of advertisement boards, tunnel pipe lines, elevated road noise barriers and barricades.
.
Performance indexes
item
index
Colloidal performance
Splitting tensile strength (MPa)
Bending strength (MPa)
Compressive strength (MPa)
≥8.5
≥50
≥60
Adhesion performance
Steel-steel (steel sleeve) tensile anti-shear strength (MPa)
Under the constraint drawing condition, ribbed steel bars and C30, φ25, L=150mm (MPa)
Adhesion strength of concrete C60, φ25, L=125mm (MPa)
≥16
≥11
≥17
Non-volatile matter content (solid content) (%)
≥99.5
Construction technical indexes
rebar diameter(mmm)
10
12
14
16
18
20
22
25
28
30
drill hole diameter(mm)
14
18
20
22
25
28
30
32
35
37
tension desiger(KN)
depth 10d
19.5
27.7
36.2
50.1
61.5
81.1
98.2
125.2
155.3
190.8
depth 15d
24.2
33.1
46.9
61.8
77.7
96.5
116.8
149.3
187.5
236.1
Epoxy resin Injective glues
1.Bicomponent modified epoxy resin injection anchor adhesive
2.Not contain styrene, non-toxic
3.Good thixotropy
4.Convenie
1.
Product Characteristics
1) Modified epoxy resin, not contain styrene, safe and non-toxic
2) High strength, strong cohesion, good toughness, effect is equivalent to embedded.
3) Aging resistance, good heat-resistant performance, creep does not occur at room temperature.
4) Low moisture sensitivity, long-term load stability in a damp environment.
5) Acid-alkali resistance, good seismic resistance performance, no expansion.
6) Good thixotropy, especially suitable for anchoring the side or top.
7) Binocular straight mixed package, with special glue gun, not need prepare glue manually.
2.
Application
Range
1) The planting of steel bars and bolts in concrete’s frame member.
2) The fixation of drying hanging brackets of curtain walls and stone materials.
3) The reinforcement of building structures and the anchorage of framework.
4) The basic fixation of many equipments.
5) The anchoring connection of steel structures and concrete structures.
6) The engineering reinforcement of railways, public roads, bridges, water conservancy facilities’ reconstruction and extension, etc.
7) The fixation of advertisement boards, tunnel pipe lines, elevated road noise barriers and barricades.
.
Performance indexes
item
index
Colloidal performance
Splitting tensile strength (MPa)
Bending strength (MPa)
Compressive strength (MPa)
≥8.5
≥50
≥60
Adhesion performance
Steel-steel (steel sleeve) tensile anti-shear strength (MPa)
Under the constraint drawing condition, ribbed steel bars and C30, φ25, L=150mm (MPa)
Adhesion strength of concrete C60, φ25, L=125mm (MPa)
≥16
≥11
≥17
Non-volatile matter content (solid content) (%)
≥99.5
Construction technical indexes
rebar diameter(mmm)
10
12
14
16
18
20
22
25
28
30
drill hole diameter(mm)
14
18
20
22
25
28
30
32
35
37
tension desiger(KN)
depth 10d
19.5
27.7
36.2
50.1
61.5
81.1
98.2
125.2
155.3
190.8
depth 15d
24.2
33.1
46.9
61.8
77.7
96.5
116.8
149.3
187.5
236.1
2.Not contain styrene, non-toxic
3.Good thixotropy
4.Convenie
1.
Product Characteristics
1) Modified epoxy resin, not contain styrene, safe and non-toxic
2) High strength, strong cohesion, good toughness, effect is equivalent to embedded.
3) Aging resistance, good heat-resistant performance, creep does not occur at room temperature.
4) Low moisture sensitivity, long-term load stability in a damp environment.
5) Acid-alkali resistance, good seismic resistance performance, no expansion.
6) Good thixotropy, especially suitable for anchoring the side or top.
7) Binocular straight mixed package, with special glue gun, not need prepare glue manually.
2.
Application
Range
1) The planting of steel bars and bolts in concrete’s frame member.
2) The fixation of drying hanging brackets of curtain walls and stone materials.
3) The reinforcement of building structures and the anchorage of framework.
4) The basic fixation of many equipments.
5) The anchoring connection of steel structures and concrete structures.
6) The engineering reinforcement of railways, public roads, bridges, water conservancy facilities’ reconstruction and extension, etc.
7) The fixation of advertisement boards, tunnel pipe lines, elevated road noise barriers and barricades.
.
Performance indexes
item
index
Colloidal performance
Splitting tensile strength (MPa)
Bending strength (MPa)
Compressive strength (MPa)
≥8.5
≥50
≥60
Adhesion performance
Steel-steel (steel sleeve) tensile anti-shear strength (MPa)
Under the constraint drawing condition, ribbed steel bars and C30, φ25, L=150mm (MPa)
Adhesion strength of concrete C60, φ25, L=125mm (MPa)
≥16
≥11
≥17
Non-volatile matter content (solid content) (%)
≥99.5
Construction technical indexes
rebar diameter(mmm)
10
12
14
16
18
20
22
25
28
30
drill hole diameter(mm)
14
18
20
22
25
28
30
32
35
37
tension desiger(KN)
depth 10d
19.5
27.7
36.2
50.1
61.5
81.1
98.2
125.2
155.3
190.8
depth 15d
24.2
33.1
46.9
61.8
77.7
96.5
116.8
149.3
187.5
236.1
1pc/card krazy glue
packing: 1pc/card, 12card/ gift box, 12 box/carton
delivert time: 30 days
meas:28*23*36cm/144card
quan: 175248card/20'
Super Glue
suits for plastic,rubber,metal,leather,ceramic,wood and so on.
our production can made under your trade mark.
Item name
super glue
Item no.
JYA-001
application
For WOOD,RUBBER,PLASTIC,METAL PAPER,AND LEATHER
Weight
1-3g
package
1pc/card, 12card/ gift box,12box/carton
measurement
28*23*36cm
OEM
Available
Appearance
liquid,clear
Shelf life
12 months
Certification
SGS
Application
:
Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure.
Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis-sue paper. Keep out of reach of children, in cool dry place
Warning:
Keep out of reach of children:
Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm warter and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor.
Bond for home uses
:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
delivert time: 30 days
meas:28*23*36cm/144card
quan: 175248card/20'
Super Glue
suits for plastic,rubber,metal,leather,ceramic,wood and so on.
our production can made under your trade mark.
Item name
super glue
Item no.
JYA-001
application
For WOOD,RUBBER,PLASTIC,METAL PAPER,AND LEATHER
Weight
1-3g
package
1pc/card, 12card/ gift box,12box/carton
measurement
28*23*36cm
OEM
Available
Appearance
liquid,clear
Shelf life
12 months
Certification
SGS
Application
:
Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure.
Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis-sue paper. Keep out of reach of children, in cool dry place
Warning:
Keep out of reach of children:
Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm warter and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor.
Bond for home uses
:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
Epoxy resin and hardener
1.superior insulation property
2.low shrinkage
3.shiny appearance
4.good crack resistance
Two-component potting compound (10:2).
Curing condition (h/°C): 8~10/23
Thermal resisting class: F
This epoxy resin compound is designed for potting coils of small sized transformers and mutual inductors, and ignition coils of motorcycles and automotives, etc. Meanwhile, it is also applied to potting electronic elements.
Fire retardant potting materials are also available here.
2.low shrinkage
3.shiny appearance
4.good crack resistance
Two-component potting compound (10:2).
Curing condition (h/°C): 8~10/23
Thermal resisting class: F
This epoxy resin compound is designed for potting coils of small sized transformers and mutual inductors, and ignition coils of motorcycles and automotives, etc. Meanwhile, it is also applied to potting electronic elements.
Fire retardant potting materials are also available here.
Epoxy resin carbon fibre adhesive XQ-XW
Carbon fiber adhesives special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue.
carbon fiber adhesive, carbon fibre adhesive, carbon fiber glue,
Carbon fiber adhesives are special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue and repair glue.
The main components of the basic glue are modified epoxy resin, used for the anchoring on the concrete surface before paste on the carbon fiber cloth, it can penetrate into the concrete surface, improve the entire stress effects between the surface and cloth.
Features:
1. Tensile strength 10 times than regular steel materials, modulus of elasticity similar to steel, can be used for anchoring the steel bar into concrete;
2. Widely used for anti-bonding, anti-shearing, anti compression, anti-seismic
3. Only 1/4 of Steel weight, each layer thickness less than 1mm, no extra weight and sizes needed;
4. No need for large equipment, shorten the construction period,
Specification:
Specs: A (main) transparent liquid, B (hardener) burgundy liquid
Mixture Viscosity: 4000 – 6000mPa.S
Solids density: 1.10 +/- 0.10g/cm3
Mixing (weighing) ratio: 2:1
Shelf expired: 12 months
Handling time (25 C.degree): ≥90
Project
Index
Steel bar and the concrete bond strength (Mpa)
≥14
Tensile bond strength with concrete (Mpa)
≥2.5
Solids content %
≥99
Packing details:
Double components packed separately in barrels, 20kgs/set and 100kgs/set.
carbon fiber adhesive, carbon fibre adhesive, carbon fiber glue,
Carbon fiber adhesives are special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue and repair glue.
The main components of the basic glue are modified epoxy resin, used for the anchoring on the concrete surface before paste on the carbon fiber cloth, it can penetrate into the concrete surface, improve the entire stress effects between the surface and cloth.
Features:
1. Tensile strength 10 times than regular steel materials, modulus of elasticity similar to steel, can be used for anchoring the steel bar into concrete;
2. Widely used for anti-bonding, anti-shearing, anti compression, anti-seismic
3. Only 1/4 of Steel weight, each layer thickness less than 1mm, no extra weight and sizes needed;
4. No need for large equipment, shorten the construction period,
Specification:
Specs: A (main) transparent liquid, B (hardener) burgundy liquid
Mixture Viscosity: 4000 – 6000mPa.S
Solids density: 1.10 +/- 0.10g/cm3
Mixing (weighing) ratio: 2:1
Shelf expired: 12 months
Handling time (25 C.degree): ≥90
Project
Index
Steel bar and the concrete bond strength (Mpa)
≥14
Tensile bond strength with concrete (Mpa)
≥2.5
Solids content %
≥99
Packing details:
Double components packed separately in barrels, 20kgs/set and 100kgs/set.
Epoxy resin carbon fibre glue XQ-XW
Carbon fiber adhesives special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue.
Carbon fiber adhesives are special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue and repair glue.
The main components of the basic glue are modified epoxy resin, used for the anchoring on the concrete surface before paste on the carbon fiber cloth, it can penetrate into the concrete surface, improve the entire stress effects between the surface and cloth.
Features:
1. Tensile strength 10 times than regular steel materials, modulus of elasticity similar to steel, can be used for anchoring the steel bar into concrete;
2. Widely used for anti-bonding, anti-shearing, anti compression, anti-seismic
3. Only 1/4 of Steel weight, each layer thickness less than 1mm, no extra weight and sizes needed;
4. No need for large equipment, shorten the construction period,
Specification:
Specs: A (main) transparent liquid, B (hardener) burgundy liquid
Mixture Viscosity: 4000 – 6000mPa.S
Solids density: 1.10 +/- 0.10g/cm3
Mixing (weighing) ratio: 2:1
Shelf expired: 12 months
Handling time (25 C.degree): ≥90
Project
Index
Steel bar and the concrete bond strength (Mpa)
≥14
Tensile bond strength with concrete (Mpa)
≥2.5
Solids content %
≥99
Packing details:
Double components packed separately in barrels, 20kgs/set and 100kgs/set.
Carbon fiber adhesives are special glues for construction anchoring with carbon fiber cloth, include basic glue, immersing glue and repair glue.
The main components of the basic glue are modified epoxy resin, used for the anchoring on the concrete surface before paste on the carbon fiber cloth, it can penetrate into the concrete surface, improve the entire stress effects between the surface and cloth.
Features:
1. Tensile strength 10 times than regular steel materials, modulus of elasticity similar to steel, can be used for anchoring the steel bar into concrete;
2. Widely used for anti-bonding, anti-shearing, anti compression, anti-seismic
3. Only 1/4 of Steel weight, each layer thickness less than 1mm, no extra weight and sizes needed;
4. No need for large equipment, shorten the construction period,
Specification:
Specs: A (main) transparent liquid, B (hardener) burgundy liquid
Mixture Viscosity: 4000 – 6000mPa.S
Solids density: 1.10 +/- 0.10g/cm3
Mixing (weighing) ratio: 2:1
Shelf expired: 12 months
Handling time (25 C.degree): ≥90
Project
Index
Steel bar and the concrete bond strength (Mpa)
≥14
Tensile bond strength with concrete (Mpa)
≥2.5
Solids content %
≥99
Packing details:
Double components packed separately in barrels, 20kgs/set and 100kgs/set.
Epoxy resin
* used on metal
* used on glass
* used on ceramic
* used on wood
* used on electronic components
Epoxy Resin
A fast-curing transparent, two-component epoxy resin adhesive providing high bond strength combined with residual elasticity 3-5 mins dry, and it can be used to adhere the copper, brass, plasticand so on.
* used on glass
* used on ceramic
* used on wood
* used on electronic components
Epoxy Resin
A fast-curing transparent, two-component epoxy resin adhesive providing high bond strength combined with residual elasticity 3-5 mins dry, and it can be used to adhere the copper, brass, plasticand so on.
Epoxy resinwaterproof adhesive
1)Good bonding and strongly permeate
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
Epoxy steel adhesive,Epoxy AB glue
Epoxy steel adhesive
Araldite on curing speed of 5minute
it is very convenience and easy to use
Epoxy adhesives combine exceotinal strength and durability. Bonds trim and ornaments.Resistant to gasoline,anti-freeze and most solvents.
DIRECTIONS:
1.Surface to be repaired must be clean ,dry and freeof oil ,grease or wax .
2. Remove cap and puncyure seal of both RESIN and HARDENER
3.Squeeze equal amounts from both tubes noto a clean surface and mix thoroughly until a uniform color is a achieved.EAGLESTAR Epoxysteel sets in 5 minutes mix only what can be uses within this frame.
4.Spread on a thin coat to both surfaces .no clamp is necessary-apply slight pressure until it sets.
Araldite on curing speed of 5minute
it is very convenience and easy to use
Epoxy adhesives combine exceotinal strength and durability. Bonds trim and ornaments.Resistant to gasoline,anti-freeze and most solvents.
DIRECTIONS:
1.Surface to be repaired must be clean ,dry and freeof oil ,grease or wax .
2. Remove cap and puncyure seal of both RESIN and HARDENER
3.Squeeze equal amounts from both tubes noto a clean surface and mix thoroughly until a uniform color is a achieved.EAGLESTAR Epoxysteel sets in 5 minutes mix only what can be uses within this frame.
4.Spread on a thin coat to both surfaces .no clamp is necessary-apply slight pressure until it sets.
Epoxy steel adhesive
Epoxy steel adhesive
Araldite on curing speed of 5minute
Epoxy adhesives combine exceotinal strength and durability. Bonds trim and ornaments.Resistant to gasoline,anti-freeze and most solvents.
DIRECTIONS:
1.Surface to be repaired must be clean ,dry and freeof oil ,grease or wax .
2. Remove cap and puncyure seal of both RESIN and HARDENER
3.Squeeze equal amounts from both tubes noto a clean surface and mix thoroughly until a uniform color is a achieved.EAGLESTAR Epoxysteel sets in 5 minutes mix only what can be uses within this frame.
4.Spread on a thin coat to both surfaces .no clamp is necessary-apply slight pressure until it sets.
Araldite on curing speed of 5minute
Epoxy adhesives combine exceotinal strength and durability. Bonds trim and ornaments.Resistant to gasoline,anti-freeze and most solvents.
DIRECTIONS:
1.Surface to be repaired must be clean ,dry and freeof oil ,grease or wax .
2. Remove cap and puncyure seal of both RESIN and HARDENER
3.Squeeze equal amounts from both tubes noto a clean surface and mix thoroughly until a uniform color is a achieved.EAGLESTAR Epoxysteel sets in 5 minutes mix only what can be uses within this frame.
4.Spread on a thin coat to both surfaces .no clamp is necessary-apply slight pressure until it sets.
Epoxy
Sealing Adhesive,Jewel Glue,
Stone Glue,Marble Glue
EPOXY ADHESIVE 6812
AB-6812 into two liquid type epoxy resin without volatile, with many excellent features, as follows:
1, Colorless or white, low viscosity, non-volatile, and the operating time is long.
2, With most metal, plastic products with good adhesion.
3, Soft and resilient after hardening, impact resistance and friction with the finished product.
4, Finished with high gloss surface hardening, have excellent resistance to cleaning properties.
5, Apply decorative and protective coating.
Features:
6812-A
6812-B
Appearance
Clear or White Liquid
Clear Liquid
Viscosity(25°C,CPS)
500-3000
50-700
Flash point (°C)
more than 300c
more than 150
Mix Ratio(P.H.R)
60
30
Operationg Time
30-40 mins
----
Curing condiction
Room temp.: 8-10 hours 70°C: 90 mins
----
Instructions for use:
1, Prepare a clean container and blender (stick blender can be material or mechanical)
2, Weight the required A-6812 and B-6812, 2:1 ratio of the amount.
3, Mixing.
4, Put the mixture into the required infusion or wrap the material.
5, It can be hardened at room temperature or heated.
Stone Glue,Marble Glue
EPOXY ADHESIVE 6812
AB-6812 into two liquid type epoxy resin without volatile, with many excellent features, as follows:
1, Colorless or white, low viscosity, non-volatile, and the operating time is long.
2, With most metal, plastic products with good adhesion.
3, Soft and resilient after hardening, impact resistance and friction with the finished product.
4, Finished with high gloss surface hardening, have excellent resistance to cleaning properties.
5, Apply decorative and protective coating.
Features:
6812-A
6812-B
Appearance
Clear or White Liquid
Clear Liquid
Viscosity(25°C,CPS)
500-3000
50-700
Flash point (°C)
more than 300c
more than 150
Mix Ratio(P.H.R)
60
30
Operationg Time
30-40 mins
----
Curing condiction
Room temp.: 8-10 hours 70°C: 90 mins
----
Instructions for use:
1, Prepare a clean container and blender (stick blender can be material or mechanical)
2, Weight the required A-6812 and B-6812, 2:1 ratio of the amount.
3, Mixing.
4, Put the mixture into the required infusion or wrap the material.
5, It can be hardened at room temperature or heated.
Ethyl silicate-28(10000MT/YEAR)
ethyl silicate40
ethyl silicate32
ethyl silicate28
200kg/iron. 16000kg/FCL
ethyl silicate40
ethyl silicate32
ethyl silicate28
200kg/iron. 16000kg/FCL
Index name
Index
Appearance
colorless transparent liquit
Chroma(APHA)
20
Specific gravityat 20° C(68° F)
1.05-1.07
Silicon dioxide content
40-42%
Acidity(as HCl)
0.01
Alcohol
1%
Other content
0-5ppm
Viscidity( 20°C)
4-7cps.
ethyl silicate32
ethyl silicate28
200kg/iron. 16000kg/FCL
ethyl silicate40
ethyl silicate32
ethyl silicate28
200kg/iron. 16000kg/FCL
Index name
Index
Appearance
colorless transparent liquit
Chroma(APHA)
20
Specific gravityat 20° C(68° F)
1.05-1.07
Silicon dioxide content
40-42%
Acidity(as HCl)
0.01
Alcohol
1%
Other content
0-5ppm
Viscidity( 20°C)
4-7cps.
Everlasting Epoxy Resin
Favorable price and trustworthy quality.
Good and safe package, quick and smooth delivery.
Ideal for long-term cooperation
No.
specification
superior quality
qualified
1
exterior appearance
pure, transparency liquid
2
epoxy value Eq/100g
0.43~0.47(213~232)
0.42~0.47(213~248)
3
impurities content (150°C,40mins),% ≤
1.0
1.0
4
inorganic chlorine value Eq/100g≤
0.001
0.001
5
organic chlorine value Eq/101g≤
0.01
0.02
6
softening point, °C
12~20
12~20
7
color(Pt-Co color)hazen ≤
50
100
8
viscosity(40°C) mPa·s
~
~
9
solidified time under 200°C
depends
10
gel time (min)
depends
Epoxy:
Instructions
Get the dust and grease off from the stone surface.
Mix A and B by the ratio of 7 to 1(calculate as weight) and daub the mixture on the surface of the stone after stirring it adequately.
3. To accelerate the curing, the stone can be heated to 50~60 possibility before daubing.
1. For big cracks, some limestone can be added as the intensifier before spreading.
2. It can be mixed into a variety of colors with adding stone toner.
Precautions
By the ratio of 7 to 1 mix A and B component, B can be excessive but not A.
Polishing or other further procedures should be processed after curing enough.
In order to avoid other chemical reactions, any chemical protection before mending or used with non-epoxy adhesive is prohibited.
Noticed not to confuse the A and B component caps and be remembered to seal up the caps tightly after using. Not for eat even by mistake!
Storage and Package
Stored in the shady, cool and airy place.
Non-inflammable and non-explosive after curing, transporting and storing should strictly according to general freight categories.
Packing Specification: A: 21Kg/barrel 7Kg/barrel
B: 3Kg/barrel 1Kg/barrel
:
Good and safe package, quick and smooth delivery.
Ideal for long-term cooperation
No.
specification
superior quality
qualified
1
exterior appearance
pure, transparency liquid
2
epoxy value Eq/100g
0.43~0.47(213~232)
0.42~0.47(213~248)
3
impurities content (150°C,40mins),% ≤
1.0
1.0
4
inorganic chlorine value Eq/100g≤
0.001
0.001
5
organic chlorine value Eq/101g≤
0.01
0.02
6
softening point, °C
12~20
12~20
7
color(Pt-Co color)hazen ≤
50
100
8
viscosity(40°C) mPa·s
~
~
9
solidified time under 200°C
depends
10
gel time (min)
depends
Epoxy:
Instructions
Get the dust and grease off from the stone surface.
Mix A and B by the ratio of 7 to 1(calculate as weight) and daub the mixture on the surface of the stone after stirring it adequately.
3. To accelerate the curing, the stone can be heated to 50~60 possibility before daubing.
1. For big cracks, some limestone can be added as the intensifier before spreading.
2. It can be mixed into a variety of colors with adding stone toner.
Precautions
By the ratio of 7 to 1 mix A and B component, B can be excessive but not A.
Polishing or other further procedures should be processed after curing enough.
In order to avoid other chemical reactions, any chemical protection before mending or used with non-epoxy adhesive is prohibited.
Noticed not to confuse the A and B component caps and be remembered to seal up the caps tightly after using. Not for eat even by mistake!
Storage and Package
Stored in the shady, cool and airy place.
Non-inflammable and non-explosive after curing, transporting and storing should strictly according to general freight categories.
Packing Specification: A: 21Kg/barrel 7Kg/barrel
B: 3Kg/barrel 1Kg/barrel
:
1pc/card Aluminum Tube Super Glue Gel
HOPSON super glue gel is suitable for bonding metal and leather,rubber,paper,electronics, fishing tackle and car fixtures.
Product name:
Super glue, Cyanoacrylate adhesive,Super adhesive, Power glue, Mini glue,Gel
Super Glue Gel
Item no.: HCA-G01
Description:
HOPSON high performance non-drip gel formula superglue works well with porous surfaces and allows for re-positioning of the adhered materials.
For bonding with pottery, glass, rubber, balsa wood, rigid plastics, casting reparation and other porous surfaces.Easy use with self piercing cap.
Application:
HOPSON super glue gel is suitable for mending dishes and household articles, furniture, fishing tackle and other sports equipment, car fixtures, electronic instruments, stone sculpture, or for use on metal, leather.
Usage:
1, Be sure the surfaces to be glued are clean and dry. 2, Apply one drop for each 3cm2 area. Apply with extreme care. Never spread with fingers. 3, Apply to only one for the surface. Quickly place two surfaces together with slight finger pressure. Bond is completed is seconds
Special:
Can produced with your own trade mark, brand name and your own artworks.
OEM is welcome.
World wide agents is welcome.
Available Packing:
Aluminum tube @2g,@3g/pcs/card, 24cards/box,24boxes/ctn
CTN: 50.8*38.0*40.0cm
KEEP OUT OF REACH OF CHILDREN.
Super glue, Cyanoacrylate adhesive,Super adhesive,Power glue, Gel Glue
Product name:
Super glue, Cyanoacrylate adhesive,Super adhesive, Power glue, Mini glue,Gel
Super Glue Gel
Item no.: HCA-G01
Description:
HOPSON high performance non-drip gel formula superglue works well with porous surfaces and allows for re-positioning of the adhered materials.
For bonding with pottery, glass, rubber, balsa wood, rigid plastics, casting reparation and other porous surfaces.Easy use with self piercing cap.
Application:
HOPSON super glue gel is suitable for mending dishes and household articles, furniture, fishing tackle and other sports equipment, car fixtures, electronic instruments, stone sculpture, or for use on metal, leather.
Usage:
1, Be sure the surfaces to be glued are clean and dry. 2, Apply one drop for each 3cm2 area. Apply with extreme care. Never spread with fingers. 3, Apply to only one for the surface. Quickly place two surfaces together with slight finger pressure. Bond is completed is seconds
Special:
Can produced with your own trade mark, brand name and your own artworks.
OEM is welcome.
World wide agents is welcome.
Available Packing:
Aluminum tube @2g,@3g/pcs/card, 24cards/box,24boxes/ctn
CTN: 50.8*38.0*40.0cm
KEEP OUT OF REACH OF CHILDREN.
Super glue, Cyanoacrylate adhesive,Super adhesive,Power glue, Gel Glue
Excellant neutral weatherproof silicone sealant(MC-1810)
MC-1810 weather-resistance silicone sealant:
1)Mantfacturer
2)Single-component
3)Excellant performance
4)Different color
A.FEATURES
lMonocomponent, RTV, expediently application between 5-40°C (directly applied by caulking gun)
lNeutral curing, medium modulus, no corrosive to glass, coated glass, concrete, marble, metal and most of the plastic materials
lExcellent resistance to movement, weather, low and high temperature change
lExcellent adhesion to most common building material even without priming, Good compatibility with other neutral silicone sealants
B.USES
Weather resistance sealing for all kinds of glass curtain wall
Weather resistance sealing for aluminum panel and ceramic curtain wall
Sealing for joints of marble (granite), concrete, tiles and metal panel
Many other building & industrial uses
C. TECH INDEX
Performance
National Standard GB/T14683-2003
Company standard Q/JH13-2005
Measured value
Tested method
Slumpability (mm)
≤3
≤2
0
GB/T13477
Extrusion(s)
≥80
≥300
300
Tack free time(min)
≤180
≤120
40
Hardness(HsA)
/
/
52
GB/T531
Loss of heating(%)
≤10
≤8
5.0
GB/T13477
Tensile strength (Mpa)
≥0.4(high modulus)
≥0.4(high modulus)
0.542
Destroy area of adhesive %
≤5
≤5
0
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Adhesion after radiation of
Non destroyed
Non destroyed
Non destroyed
Adhesion of hot strss and cold pull
Non destroyed
Non destroyed
Non destroyed
Adhesion of immersion in water
Non destroyed
Non destroyed
Non destroyed
Shelf life
Store for 9 months under 20~30oC in cool,dry place after date of manufacture
D.
COLOR AND
PACKING
Color: Black, gray, white or the other color as customer’s request;
Packing: Packed in 310 cartridge ( Net weight: 300ml ), or packed in 590ml ham bag.
E. STANDARD
China JC/T 882-2001 Curtain wall sealing silicone sealant
F.APPLICATION
Detailed operation procedure please note “The Technology Instruction of Jianhua Silicone sealant”
Project photos
1)Mantfacturer
2)Single-component
3)Excellant performance
4)Different color
A.FEATURES
lMonocomponent, RTV, expediently application between 5-40°C (directly applied by caulking gun)
lNeutral curing, medium modulus, no corrosive to glass, coated glass, concrete, marble, metal and most of the plastic materials
lExcellent resistance to movement, weather, low and high temperature change
lExcellent adhesion to most common building material even without priming, Good compatibility with other neutral silicone sealants
B.USES
Weather resistance sealing for all kinds of glass curtain wall
Weather resistance sealing for aluminum panel and ceramic curtain wall
Sealing for joints of marble (granite), concrete, tiles and metal panel
Many other building & industrial uses
C. TECH INDEX
Performance
National Standard GB/T14683-2003
Company standard Q/JH13-2005
Measured value
Tested method
Slumpability (mm)
≤3
≤2
0
GB/T13477
Extrusion(s)
≥80
≥300
300
Tack free time(min)
≤180
≤120
40
Hardness(HsA)
/
/
52
GB/T531
Loss of heating(%)
≤10
≤8
5.0
GB/T13477
Tensile strength (Mpa)
≥0.4(high modulus)
≥0.4(high modulus)
0.542
Destroy area of adhesive %
≤5
≤5
0
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Adhesion after radiation of
Non destroyed
Non destroyed
Non destroyed
Adhesion of hot strss and cold pull
Non destroyed
Non destroyed
Non destroyed
Adhesion of immersion in water
Non destroyed
Non destroyed
Non destroyed
Shelf life
Store for 9 months under 20~30oC in cool,dry place after date of manufacture
D.
COLOR AND
PACKING
Color: Black, gray, white or the other color as customer’s request;
Packing: Packed in 310 cartridge ( Net weight: 300ml ), or packed in 590ml ham bag.
E. STANDARD
China JC/T 882-2001 Curtain wall sealing silicone sealant
F.APPLICATION
Detailed operation procedure please note “The Technology Instruction of Jianhua Silicone sealant”
Project photos
Excellent PU Sealant for Auto body
Suitable for sealing & welding auto glass ang body
Bonding between automobile fittings inside and outside
TECHNICAL DATA SHEET
Testing Items
Performance
Appearance
White/Gray homogeneous paste
Density (g/cm³)
1.35±0.05
Sagging properties(mm)
≤3
Shore A-hardness(A°)
50±5
Tensile strength( Mpa)
≥1.6
Elongation at break (%)
≥350
Volatile content (%)
≤4
Touch Dry time (min)
10~30
Curing speed (mm/d)
3~5
Extrudability (g/min)
80
Pollution propertise
Non
Application temperature (ºC)
+5~+35
Shelf life(month)
≥9
All data above ware tested under standardized condition.
All data listed in the chart were for the generalized item in theseries; please refer to the related datasheet for special items.
Storage condition has a direct impact to the products’ shelf life, Please refer to the instruction for special items’ storing.
2. DESCRIPTION:
791 is one component high quality multi-purpose polyurethane sealant, it cures by reaction with atmospheric moisture to form a durable and weathering resistant elastomer, 791 is manufactured in accordance with the ISO/TS 16949:2002.
3. USES:
Suitable for car body structural bonding and sealing.
4. ADVANTAGES
:
* One-component formulation, excellent smooth appearance.
* Modest Hardness and high tensile strength after curing .-
* Flexible, durable and excellent extrudability.
* No sagging, no pollution and corrosion to base material and environment.
* Excellent sealing and adhesion performance, excellent water and aging resistance.
* Can be painted and abraded.
Bonding between automobile fittings inside and outside
TECHNICAL DATA SHEET
Testing Items
Performance
Appearance
White/Gray homogeneous paste
Density (g/cm³)
1.35±0.05
Sagging properties(mm)
≤3
Shore A-hardness(A°)
50±5
Tensile strength( Mpa)
≥1.6
Elongation at break (%)
≥350
Volatile content (%)
≤4
Touch Dry time (min)
10~30
Curing speed (mm/d)
3~5
Extrudability (g/min)
80
Pollution propertise
Non
Application temperature (ºC)
+5~+35
Shelf life(month)
≥9
All data above ware tested under standardized condition.
All data listed in the chart were for the generalized item in theseries; please refer to the related datasheet for special items.
Storage condition has a direct impact to the products’ shelf life, Please refer to the instruction for special items’ storing.
2. DESCRIPTION:
791 is one component high quality multi-purpose polyurethane sealant, it cures by reaction with atmospheric moisture to form a durable and weathering resistant elastomer, 791 is manufactured in accordance with the ISO/TS 16949:2002.
3. USES:
Suitable for car body structural bonding and sealing.
4. ADVANTAGES
:
* One-component formulation, excellent smooth appearance.
* Modest Hardness and high tensile strength after curing .-
* Flexible, durable and excellent extrudability.
* No sagging, no pollution and corrosion to base material and environment.
* Excellent sealing and adhesion performance, excellent water and aging resistance.
* Can be painted and abraded.
Exhaust system sealer/cement
repair glue,Fully adjustable, flexible repair system
Quick, clean and permanent repair without dismantling
Exhaust system sealer/cement
repair glueMUFFLER MENDER KITAND EXHAUST SYSTEM SEALER
Withstands Temperatures Up to 1100°C (2012°F)
Repairs Minor Holes and Cracks in Exhaust System resonators converters tailpipes mufflers
PART NO. GF-808
6 OZ./170g 12PCS/CASE, 12CASE/CTNRepair cement
Fully adjustable, flexible repair system
Quick, clean and permanent repair without dismantling As resonators converters tailpipes muffler Meets MOT requirements Lasts lifetime of exhaust system
Quick, clean and permanent repair without dismantling
Exhaust system sealer/cement
repair glueMUFFLER MENDER KITAND EXHAUST SYSTEM SEALER
Withstands Temperatures Up to 1100°C (2012°F)
Repairs Minor Holes and Cracks in Exhaust System resonators converters tailpipes mufflers
PART NO. GF-808
6 OZ./170g 12PCS/CASE, 12CASE/CTNRepair cement
Fully adjustable, flexible repair system
Quick, clean and permanent repair without dismantling As resonators converters tailpipes muffler Meets MOT requirements Lasts lifetime of exhaust system
Expandable foam Pu Foam Espuma
1) 500ml
2) DY06 Straw type
3) CFC free
4) High quality, competitive price
5) Environmental-friendly material
Expandable foam / Pu Foam / Espuma
is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption:0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5-6L
13) Closed cells: 60-70%
2) DY06 Straw type
3) CFC free
4) High quality, competitive price
5) Environmental-friendly material
Expandable foam / Pu Foam / Espuma
is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption:0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5-6L
13) Closed cells: 60-70%
Expanded PTFE Joint Sealant
Our corporation have the experience in producting sealing products
for more than 8 years, specializing in product .......
MS 5000.PTFE Joint seanlant
MAIN PROPERTIES
Items
unit
Property Value
Density
g/cm
3
0.7-0.85
Tensile Strength
Mpa
≥8.0
Hardness
HA
30-70
Creep Relaxation
%
≤40
Applicable Temperature
°C
-100-280
Applicable Pressure
Mpa
gas 1.6
liquid 6.4
PH RANGE
PH
Mpa
0-14
MS 5000 PTFE Joint sealant has outstanding hydro-sealing ability.It is resistant to most chemicals at a wide range of temperature and pressures from full vacuum to medium level.
It is widely applied for aero,marine,refinery,petrochemical,metallurgy,power generation,paper,pharmaceutical,foods,machine industries.Suitable for all type of genaral sealing.
for more than 8 years, specializing in product .......
MS 5000.PTFE Joint seanlant
MAIN PROPERTIES
Items
unit
Property Value
Density
g/cm
3
0.7-0.85
Tensile Strength
Mpa
≥8.0
Hardness
HA
30-70
Creep Relaxation
%
≤40
Applicable Temperature
°C
-100-280
Applicable Pressure
Mpa
gas 1.6
liquid 6.4
PH RANGE
PH
Mpa
0-14
MS 5000 PTFE Joint sealant has outstanding hydro-sealing ability.It is resistant to most chemicals at a wide range of temperature and pressures from full vacuum to medium level.
It is widely applied for aero,marine,refinery,petrochemical,metallurgy,power generation,paper,pharmaceutical,foods,machine industries.Suitable for all type of genaral sealing.
Friday, September 16, 2011
Expanded Polyurethane Foam
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expanding Chemical Foam
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expanding PU Foam Sealant
Expanding PU Foam Sealant
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service...
Product description
KNG Expanding PU Foam is a one component isolation and construction foam developed to make a seal between construction parts. The foam cures in response to humidity from air and from building materials. This versatile single component adaptor foam in aerosol cans is a practical solution for craftsmen who prefer to work without a PU Foam gun. Like all types of KNG foam the product combines excellent insulation characteristics with perfect adhesion on a wide range of substrates such as timber, brick, natural stone, concrete, plaster, metals and most plastics.
Applications
Joints between separation walls, ceiling and floors. Joints around transits of wires and piping through walls and floors. Perimeter joints around window and doorframes.
In general the foam has an excellent adhesion on concrete, brick, stone, plaster, wood, metal and many plastics like polystyrene foam, rigid PU foam and uPVC.
Technical Data
Volume:
900g/750ml
Density:
17~22kg/m3
Curing time:
2~3hours
Adhesive strength:
>80k/pa
Tensile strength:
>30k/pa
Bending strength:
>100k/pa
Compressive strength:
>120k/pa
Open cells rate:
48~55%
Oxygen index:
22~25(normal)/28~32(flame-resistant)
Permeate water volume:
0.3~1(no epidermis)/<0.1(with epidermis)
Limitations
Not recommended for locations subject to continuous water immersion and not for filling secluded areas or joints wider than 4 cm. Wider joints and joints deeper then 5 cm are to be filled in multiple layers. Waiting time between applications 15-30 minutes. Before each application lightly spray with water. The foam surface has to be protected from UVlight. Cured foam can only be removed mechanically.
Surface preparation and finishing
Surfaces must be clean and free of grease. Surfaces to be made slightly damp with a flower spray. Shake aerosol 20 times very well before use. Protect eyes and wear gloves and working clothes. Tapestry, floor-covering and furniture to be covered with paper or plastic foil. Fresh foam can be removed directly with Purfoam cleaner, thinner or acetone. After curing the surplus of the foam can be removed with a knife or spatula and the foam surface can be worked off.
Available colour
white, other on request
Packaging
300, 500, 600 en 750 ml tin aerosols with tube.
700 ml aluminium aerosols with plastic tube.
700 ml tin and aluminium aerosols with adapter for NBS-guns
Shelf Life and Storage
12 months stored in the original unopened containers between +5°C and +35°C.
Safety
Safety data sheets are available upon request.
Warranty
KNG Sealants warrants that its product complies, within its shelf life, to its specification. The liability shall in no case exceed the amount fixed in our Conditions of Sale. In no event Den Braven Sealants is liable for any incidental or consequential damage.
Liability
All supplied information is the result of our tests and experience and is of general nature. However, they do not imply any liability. It is the responsibility of the user to verify by his own tests if the product is suitable for the application.
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service...
Product description
KNG Expanding PU Foam is a one component isolation and construction foam developed to make a seal between construction parts. The foam cures in response to humidity from air and from building materials. This versatile single component adaptor foam in aerosol cans is a practical solution for craftsmen who prefer to work without a PU Foam gun. Like all types of KNG foam the product combines excellent insulation characteristics with perfect adhesion on a wide range of substrates such as timber, brick, natural stone, concrete, plaster, metals and most plastics.
Applications
Joints between separation walls, ceiling and floors. Joints around transits of wires and piping through walls and floors. Perimeter joints around window and doorframes.
In general the foam has an excellent adhesion on concrete, brick, stone, plaster, wood, metal and many plastics like polystyrene foam, rigid PU foam and uPVC.
Technical Data
Volume:
900g/750ml
Density:
17~22kg/m3
Curing time:
2~3hours
Adhesive strength:
>80k/pa
Tensile strength:
>30k/pa
Bending strength:
>100k/pa
Compressive strength:
>120k/pa
Open cells rate:
48~55%
Oxygen index:
22~25(normal)/28~32(flame-resistant)
Permeate water volume:
0.3~1(no epidermis)/<0.1(with epidermis)
Limitations
Not recommended for locations subject to continuous water immersion and not for filling secluded areas or joints wider than 4 cm. Wider joints and joints deeper then 5 cm are to be filled in multiple layers. Waiting time between applications 15-30 minutes. Before each application lightly spray with water. The foam surface has to be protected from UVlight. Cured foam can only be removed mechanically.
Surface preparation and finishing
Surfaces must be clean and free of grease. Surfaces to be made slightly damp with a flower spray. Shake aerosol 20 times very well before use. Protect eyes and wear gloves and working clothes. Tapestry, floor-covering and furniture to be covered with paper or plastic foil. Fresh foam can be removed directly with Purfoam cleaner, thinner or acetone. After curing the surplus of the foam can be removed with a knife or spatula and the foam surface can be worked off.
Available colour
white, other on request
Packaging
300, 500, 600 en 750 ml tin aerosols with tube.
700 ml aluminium aerosols with plastic tube.
700 ml tin and aluminium aerosols with adapter for NBS-guns
Shelf Life and Storage
12 months stored in the original unopened containers between +5°C and +35°C.
Safety
Safety data sheets are available upon request.
Warranty
KNG Sealants warrants that its product complies, within its shelf life, to its specification. The liability shall in no case exceed the amount fixed in our Conditions of Sale. In no event Den Braven Sealants is liable for any incidental or consequential damage.
Liability
All supplied information is the result of our tests and experience and is of general nature. However, they do not imply any liability. It is the responsibility of the user to verify by his own tests if the product is suitable for the application.
Expanding PU Foam chinese manufacturer
Expanding PU Foamone-componentPolyurethane Foam, expand foamanti-freezing, anti-moisture,noise-resistant, heat -insul
Brand Name
I-LIKE
Model Number
ID-101
Color
Champagne
surface dry time
<10 minutes
tack free time
<15 minutes
cutable time
<1 hour
hard dry time
<24 hours
temperature resistant
-40 to 90 degrees C
advantages
anti-freezing, anti-moisture, noise-resistant and heat -insulation
I-Like PU Foam is made of high quality one-component polyurethane material. It has a large expansion capacity, and can be hardened within air moisture. Its harden surface can be painted, and the temperature-resistance is from -40 to 90 .It can be adhere to all building materials and applied to insulating and filling of larger seams, joints, cracks such as gaps between walls, windows and doors, unreachable areas around pipes, etc. It has good performances in anti-freezing, anti-moisture, noise-resistant and heat -insulation.
I-Like PU Foam Sealant series include the following items:
1. Construction PU Foam;
2. Fire Proof PU Foam;
3. Winter PU Foam;
4. PU Foam Cleaner
Item No.:
ID-101
Can Size
65mm x 300mm H
Package
750ml x 12pcs/ctn
Carton Size
280x210x352 mm
20ft Container Loading
1296 cartons
Uses for Foam
Around the house
Living Space:
· Gapping baseboards
· Window & door frames
· Around electrical junction boxes (not inside them!)
· Wire and pipe penetrations
· Air, heating and dryer vents
Basements/Attics:
· Pipe and duct penetrations
· Plumbing stacks and shafts
· Wall cracks
· Along the sillplate and floor/wall junction
Outside
Exterior Home:
· At the bottom of your siding edge, where it meets the foundation
· Electric, gas and A/C penetrations
· Along garage ceiling and wall joints
· Faucets
· Dryer vents
Landscaping:
· In holes in trees, to slow rot and prevent infestation
· Securing landscape blocks
· Stone wall repair
· Koi ponds, waterfalls, and fountains; for repairs or directing water flow
Creative Arts and Crafts
· Creating sculptures
· Artificial rocks for landscaping
· Securing silk floral arrangements
· Halloween costumes and props
Brand Name
I-LIKE
Model Number
ID-101
Color
Champagne
surface dry time
<10 minutes
tack free time
<15 minutes
cutable time
<1 hour
hard dry time
<24 hours
temperature resistant
-40 to 90 degrees C
advantages
anti-freezing, anti-moisture, noise-resistant and heat -insulation
I-Like PU Foam is made of high quality one-component polyurethane material. It has a large expansion capacity, and can be hardened within air moisture. Its harden surface can be painted, and the temperature-resistance is from -40 to 90 .It can be adhere to all building materials and applied to insulating and filling of larger seams, joints, cracks such as gaps between walls, windows and doors, unreachable areas around pipes, etc. It has good performances in anti-freezing, anti-moisture, noise-resistant and heat -insulation.
I-Like PU Foam Sealant series include the following items:
1. Construction PU Foam;
2. Fire Proof PU Foam;
3. Winter PU Foam;
4. PU Foam Cleaner
Item No.:
ID-101
Can Size
65mm x 300mm H
Package
750ml x 12pcs/ctn
Carton Size
280x210x352 mm
20ft Container Loading
1296 cartons
Uses for Foam
Around the house
Living Space:
· Gapping baseboards
· Window & door frames
· Around electrical junction boxes (not inside them!)
· Wire and pipe penetrations
· Air, heating and dryer vents
Basements/Attics:
· Pipe and duct penetrations
· Plumbing stacks and shafts
· Wall cracks
· Along the sillplate and floor/wall junction
Outside
Exterior Home:
· At the bottom of your siding edge, where it meets the foundation
· Electric, gas and A/C penetrations
· Along garage ceiling and wall joints
· Faucets
· Dryer vents
Landscaping:
· In holes in trees, to slow rot and prevent infestation
· Securing landscape blocks
· Stone wall repair
· Koi ponds, waterfalls, and fountains; for repairs or directing water flow
Creative Arts and Crafts
· Creating sculptures
· Artificial rocks for landscaping
· Securing silk floral arrangements
· Halloween costumes and props
Expanding PU Foam
Expanding PU Foam
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service...
Product description
KNG Expanding PU Foam is a one component isolation and construction foam developed to make a seal between construction parts. The foam cures in response to humidity from air and from building materials. This versatile single component adaptor foam in aerosol cans is a practical solution for craftsmen who prefer to work without a PU Foam gun. Like all types of KNG foam the product combines excellent insulation characteristics with perfect adhesion on a wide range of substrates such as timber, brick, natural stone, concrete, plaster, metals and most plastics.
Applications
Joints between separation walls, ceiling and floors. Joints around transits of wires and piping through walls and floors. Perimeter joints around window and doorframes.
In general the foam has an excellent adhesion on concrete, brick, stone, plaster, wood, metal and many plastics like polystyrene foam, rigid PU foam and uPVC.
Technical Data
Volume:
900g/750ml
Density:
17~22kg/m3
Curing time:
2~3hours
Adhesive strength:
>80k/pa
Tensile strength:
>30k/pa
Bending strength:
>100k/pa
Compressive strength:
>120k/pa
Open cells rate:
48~55%
Oxygen index:
22~25(normal)/28~32(flame-resistant)
Permeate water volume:
0.3~1(no epidermis)/<0.1(with epidermis)
Limitations
Not recommended for locations subject to continuous water immersion and not for filling secluded areas or joints wider than 4 cm. Wider joints and joints deeper then 5 cm are to be filled in multiple layers. Waiting time between applications 15-30 minutes. Before each application lightly spray with water. The foam surface has to be protected from UVlight. Cured foam can only be removed mechanically.
Surface preparation and finishing
Surfaces must be clean and free of grease. Surfaces to be made slightly damp with a flower spray. Shake aerosol 20 times very well before use. Protect eyes and wear gloves and working clothes. Tapestry, floor-covering and furniture to be covered with paper or plastic foil. Fresh foam can be removed directly with Purfoam cleaner, thinner or acetone. After curing the surplus of the foam can be removed with a knife or spatula and the foam surface can be worked off.
Available colour
white, other on request
Packaging
300, 500, 600 en 750 ml tin aerosols with tube.
700 ml aluminium aerosols with plastic tube.
700 ml tin and aluminium aerosols with adapter for NBS-guns
Shelf Life and Storage
12 months stored in the original unopened containers between +5°C and +35°C.
Safety
Safety data sheets are available upon request.
Warranty
KNG Sealants warrants that its product complies, within its shelf life, to its specification. The liability shall in no case exceed the amount fixed in our Conditions of Sale. In no event Den Braven Sealants is liable for any incidental or consequential damage.
Liability
All supplied information is the result of our tests and experience and is of general nature. However, they do not imply any liability. It is the responsibility of the user to verify by his own tests if the product is suitable for the application.
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service...
Product description
KNG Expanding PU Foam is a one component isolation and construction foam developed to make a seal between construction parts. The foam cures in response to humidity from air and from building materials. This versatile single component adaptor foam in aerosol cans is a practical solution for craftsmen who prefer to work without a PU Foam gun. Like all types of KNG foam the product combines excellent insulation characteristics with perfect adhesion on a wide range of substrates such as timber, brick, natural stone, concrete, plaster, metals and most plastics.
Applications
Joints between separation walls, ceiling and floors. Joints around transits of wires and piping through walls and floors. Perimeter joints around window and doorframes.
In general the foam has an excellent adhesion on concrete, brick, stone, plaster, wood, metal and many plastics like polystyrene foam, rigid PU foam and uPVC.
Technical Data
Volume:
900g/750ml
Density:
17~22kg/m3
Curing time:
2~3hours
Adhesive strength:
>80k/pa
Tensile strength:
>30k/pa
Bending strength:
>100k/pa
Compressive strength:
>120k/pa
Open cells rate:
48~55%
Oxygen index:
22~25(normal)/28~32(flame-resistant)
Permeate water volume:
0.3~1(no epidermis)/<0.1(with epidermis)
Limitations
Not recommended for locations subject to continuous water immersion and not for filling secluded areas or joints wider than 4 cm. Wider joints and joints deeper then 5 cm are to be filled in multiple layers. Waiting time between applications 15-30 minutes. Before each application lightly spray with water. The foam surface has to be protected from UVlight. Cured foam can only be removed mechanically.
Surface preparation and finishing
Surfaces must be clean and free of grease. Surfaces to be made slightly damp with a flower spray. Shake aerosol 20 times very well before use. Protect eyes and wear gloves and working clothes. Tapestry, floor-covering and furniture to be covered with paper or plastic foil. Fresh foam can be removed directly with Purfoam cleaner, thinner or acetone. After curing the surplus of the foam can be removed with a knife or spatula and the foam surface can be worked off.
Available colour
white, other on request
Packaging
300, 500, 600 en 750 ml tin aerosols with tube.
700 ml aluminium aerosols with plastic tube.
700 ml tin and aluminium aerosols with adapter for NBS-guns
Shelf Life and Storage
12 months stored in the original unopened containers between +5°C and +35°C.
Safety
Safety data sheets are available upon request.
Warranty
KNG Sealants warrants that its product complies, within its shelf life, to its specification. The liability shall in no case exceed the amount fixed in our Conditions of Sale. In no event Den Braven Sealants is liable for any incidental or consequential damage.
Liability
All supplied information is the result of our tests and experience and is of general nature. However, they do not imply any liability. It is the responsibility of the user to verify by his own tests if the product is suitable for the application.
1pc/card Aluminum tube Super Glue
HOPSON super glue products are suitable for mending dishes and household articles, furniture, fishing tackle and car fixtures.
Product name:
Super glue, Cyanoacrylate adhesive, Super adhesive, Power glue
Item no.: HCA-001B
Description:
HOPSON super glue aluminum tube series
HOPSON Super Glue is a single-component cyanoacrylate monomer in the liquid state capable of extremely rapid polymerization between adherent surfaces, resulting in extremely strong and structural bonds at room temperature.
Application:
HOPSON super glue products are suitable for mending dishes and household articles, furniture, fishing tackle and other sports equipment, car fixtures, electronic instruments, stone sculpture, or for use on metal, leather or paper.
Usage:
1, Be sure the surfaces to be glued are clean and dry.
]2, Apply one drop for each 3cm2 area. Apply with extreme care. Never spread with fingers.
3, Apply to only one for the surface. Quickly place two surfaces together with slight finger pressure. Bond is completed is seconds
Special:
Can produced with your own trade mark, brand name and your own artworks.
OEM is welcome.
World wide agents is welcome.
Available Packing:
Aluminum tube @ 2g /pcs, @3g/pcs
24cards/box, 24boxes/ctn
CTN: 69.0*39.0*28.5cm
KEEP OUT OF REACH OF CHILDREN.
Super glue, Cyanoacrylate adhesive, Super adhesive, Power glue
Product name:
Super glue, Cyanoacrylate adhesive, Super adhesive, Power glue
Item no.: HCA-001B
Description:
HOPSON super glue aluminum tube series
HOPSON Super Glue is a single-component cyanoacrylate monomer in the liquid state capable of extremely rapid polymerization between adherent surfaces, resulting in extremely strong and structural bonds at room temperature.
Application:
HOPSON super glue products are suitable for mending dishes and household articles, furniture, fishing tackle and other sports equipment, car fixtures, electronic instruments, stone sculpture, or for use on metal, leather or paper.
Usage:
1, Be sure the surfaces to be glued are clean and dry.
]2, Apply one drop for each 3cm2 area. Apply with extreme care. Never spread with fingers.
3, Apply to only one for the surface. Quickly place two surfaces together with slight finger pressure. Bond is completed is seconds
Special:
Can produced with your own trade mark, brand name and your own artworks.
OEM is welcome.
World wide agents is welcome.
Available Packing:
Aluminum tube @ 2g /pcs, @3g/pcs
24cards/box, 24boxes/ctn
CTN: 69.0*39.0*28.5cm
KEEP OUT OF REACH OF CHILDREN.
Super glue, Cyanoacrylate adhesive, Super adhesive, Power glue
Expanding PU Foam
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expanding PU Foam
Expanding PU Foam
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
noise-resistant, heat -insu
I-Like PU Foam is made of high quality one-component polyurethane material. It has a large expansion capacity, and can be hardened within air moisture. Its harden surface can be painted, and the temperature-resistance is from -40 to 90 .It can be adhere to all building materials and applied to insulating and filling of larger seams, joints, cracks such as gaps between walls, windows and doors, unreachable areas around pipes, etc. It has good performances in anti-freezing, anti-moisture, noise-resistant and heat -insulation.
I-Like PU Foam Sealant series include the following items:
1. Construction PU Foam;
2. Fire Proof PU Foam;
3. Winter PU Foam;
4. PU Foam Cleaner
Item No.:
ID-101
Can Size
65mm x 300mm H
Package
750ml x 12pcs/ctn
Carton Size
280x210x352 mm
20ft Container Loading
1380 cartons
Uses for Foam
Around the house
Living Space:
Gapping baseboards
Window & door frames
Around electrical junction boxes (not inside them!)
Wire and pipe penetrations
Air, heating and dryer vents
Basements/Attics:
Pipe and duct penetrations
Plumbing stacks and shafts
Wall cracks
Along the sillplate and floor/wall junction
Outside
Exterior Home:
At the bottom of your siding edge, where it meets the foundation
Electric, gas and A/C penetrations
Along garage ceiling and wall joints
Faucets
Dryer vents
Landscaping:
In holes in trees, to slow rot and prevent infestation
Securing landscape blocks
Stone wall repair
Koi ponds, waterfalls, and fountains; for repairs or directing water flow
Creative Arts and Crafts
Creating sculptures
Artificial rocks for landscaping
Securing silk floral arrangements
Halloween costumes and props
one-component
Polyurethane Foam, expand foam
anti-freezing, anti-moisture,
noise-resistant, heat -insu
I-Like PU Foam is made of high quality one-component polyurethane material. It has a large expansion capacity, and can be hardened within air moisture. Its harden surface can be painted, and the temperature-resistance is from -40 to 90 .It can be adhere to all building materials and applied to insulating and filling of larger seams, joints, cracks such as gaps between walls, windows and doors, unreachable areas around pipes, etc. It has good performances in anti-freezing, anti-moisture, noise-resistant and heat -insulation.
I-Like PU Foam Sealant series include the following items:
1. Construction PU Foam;
2. Fire Proof PU Foam;
3. Winter PU Foam;
4. PU Foam Cleaner
Item No.:
ID-101
Can Size
65mm x 300mm H
Package
750ml x 12pcs/ctn
Carton Size
280x210x352 mm
20ft Container Loading
1380 cartons
Uses for Foam
Around the house
Living Space:
Gapping baseboards
Window & door frames
Around electrical junction boxes (not inside them!)
Wire and pipe penetrations
Air, heating and dryer vents
Basements/Attics:
Pipe and duct penetrations
Plumbing stacks and shafts
Wall cracks
Along the sillplate and floor/wall junction
Outside
Exterior Home:
At the bottom of your siding edge, where it meets the foundation
Electric, gas and A/C penetrations
Along garage ceiling and wall joints
Faucets
Dryer vents
Landscaping:
In holes in trees, to slow rot and prevent infestation
Securing landscape blocks
Stone wall repair
Koi ponds, waterfalls, and fountains; for repairs or directing water flow
Creative Arts and Crafts
Creating sculptures
Artificial rocks for landscaping
Securing silk floral arrangements
Halloween costumes and props
Expanding Polyurethane Sealant
1 750ml
2 CFC free
3 Factory directly sell
4 High quality, competitive price
5 Environmental-friendly material
Pu foam spray / Poliuretano / PU sealant
is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2 CFC free
3 Factory directly sell
4 High quality, competitive price
5 Environmental-friendly material
Pu foam spray / Poliuretano / PU sealant
is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expanding Spray Foam
1) 750ml
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2) CFC free
3) Large expansion capacity
4) Best price and quality
5) Fast delivery and good service
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expanding Spray PU Foam Sealant
1 750ml
2 CFC free
3 Factory directly sell
4 High quality, competitive price
5 Environmental-friendly material
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
2 CFC free
3 Factory directly sell
4 High quality, competitive price
5 Environmental-friendly material
One component expanding PU Foam is a multi-purpose polyurethane foam
that may be used for a wide range of building applications, such as
filling gaps around pipes, draft proofing and sealing window and door
frames, bonding wood and brick and sealing cracks and crevices. Adhesion
is good to most construction surfaces, such as wood, brick, concrete,
metals and many plastics. When cured it is weather and rot proof and
can be trimmed, sawn, sanded and, if necessary, painted and plastered.
PU foam will cure when moisture in the air reacts with the chemicals
of the foam. All one-component foams meet GB8624-97 flame resistance
requirements for caulks and sealants. We occupy 60-70% of the domestic
market and are one of the largest suppliers in Asia.
Guide for use:
It can be applied to damp surfaces. OCF is moisture curing. The more
moisture, the quicker the cure. It must be protected from Uvin external
application to prevent discoloration and deterioration of the foam.
Conventional paints can be applied to the foam. In overhead applications,
foam must be retained in place to prevent its falling away until adhesion
grips. It can be used in temperature range of 5-40
o
C, if in
low temperature condition, we suggest that it should be placed in
25-30
o
C circumstance for 30 minutes to ensure the better
performance. Uncured foam can be removed with solvent. But after cure,
foam can only be removed mechanically (sanded or scraped off). Uncured
foam sticks to hands and clothing.
Specifications:
1) Storage life: 12 months when stored at 20
o
C
2) 12 or 15 cans/carton
3) Density: 14 to 30kg/m
3
4) Adhesive strength: PVC-PVC: 143kPa
5) Aluminum plates: 133kPa
6) Elongation at break: 8-20%
7) Shear strength: 22-50kPa
8) Compression strength 35-100kPa at 10% compression
9) Water absorption: 0.03% volume
10) Thermo conductivity: 0.028-0.038W/(m.k)
11) Tack free time: 12mins at 23
o
C/50%RH
12) Yield per 100 ml: 5 - 6L
13) Closed cells: 60 - 70%
Expert Manufacturer of All Purpose Adhesive Contact Adhesive
It is suitable for binding:
1.aluminum-plastic-board,fire resistant board
2.veneer-wood,quick-dry-board,stone-surface-board
JinWanDe
ADV Multi-purpose Adhesive
It is a new kind of adhesive,which is all made from imported raw materials and especially for combining of various materials
.
Outstanding Advantages
:
♣ Feature of good adhesive force
♣ Moisture and ageing resistance
♣ Friendly environment & safty
Technical Data
Appearance
Amber Liquid
Solid Content
≥ 19%
Viscosity
≥ 1000 mpa.s
Tensile Shear Strength
≥1.3 mpa
Peeling Strength
75 N/2.5cm
Storage Time
≥ 24 Months
Company Brief Introduction
Guangdong Jinwande Adhesive Co.,Ltd. is a modern enterprise adhesive production.The enterprise,established in 1986,is a development company gathering technology,production and trade in integral whole.The company mainly produce white glue,all-purpose adhesive,water-proof adhesive,latex paint,etc.The product has passed ISO9001 International Quality System certification, gained 4 national patents and reached a considerable size.The company has the ability of annual output of 50 000 tons.Its product has won high reputation in or out of national markets.
Our service aim always keep the creed of Once Combined,Never Separated, and wholeheartedly provide broad customers with excellent service
1.aluminum-plastic-board,fire resistant board
2.veneer-wood,quick-dry-board,stone-surface-board
JinWanDe
ADV Multi-purpose Adhesive
It is a new kind of adhesive,which is all made from imported raw materials and especially for combining of various materials
.
Outstanding Advantages
:
♣ Feature of good adhesive force
♣ Moisture and ageing resistance
♣ Friendly environment & safty
Technical Data
Appearance
Amber Liquid
Solid Content
≥ 19%
Viscosity
≥ 1000 mpa.s
Tensile Shear Strength
≥1.3 mpa
Peeling Strength
75 N/2.5cm
Storage Time
≥ 24 Months
Company Brief Introduction
Guangdong Jinwande Adhesive Co.,Ltd. is a modern enterprise adhesive production.The enterprise,established in 1986,is a development company gathering technology,production and trade in integral whole.The company mainly produce white glue,all-purpose adhesive,water-proof adhesive,latex paint,etc.The product has passed ISO9001 International Quality System certification, gained 4 national patents and reached a considerable size.The company has the ability of annual output of 50 000 tons.Its product has won high reputation in or out of national markets.
Our service aim always keep the creed of Once Combined,Never Separated, and wholeheartedly provide broad customers with excellent service
Eyelash Adhesive
Waterproof eyelash adhesive is clear white , dries invisibly.Changeable ordor as you like.
Item Name : Eyelash Adhesive
Item No. : HEA-001
NET. : 7g
Description :
Waterproof eyelash adhesive is clear white , dries invisibly.Changeable ordor
as you like.
Ingredients : Water,
Glycerin,
Citric Acid, Sodium Chloride,
Triethanolamine and so on.
Directions : Put on your eye shadow, mascara and eyeliner before your false eyelashes.
Apply a thin line along base of false lash. (Never apply directly to your eyelids.)
Let set for 30 seconds or until sticky. During this time, holding the lash by both
ends of the
base strip, flex it back and forth forming the shape of a horseshoe.
This contours the base of the strip to fit easily and comfortably.
Center the lash close to the base of your natural lashes and press end into
place to secure it.
Features :
Keeps lashes securely in place.
Good stickness and dries invisibly.
Safe to use,easy to clear.
1.Clear white 2. Dries invisibly 3.Easy to clear
Item Name : Eyelash Adhesive
Item No. : HEA-001
NET. : 7g
Description :
Waterproof eyelash adhesive is clear white , dries invisibly.Changeable ordor
as you like.
Ingredients : Water,
Glycerin,
Citric Acid, Sodium Chloride,
Triethanolamine and so on.
Directions : Put on your eye shadow, mascara and eyeliner before your false eyelashes.
Apply a thin line along base of false lash. (Never apply directly to your eyelids.)
Let set for 30 seconds or until sticky. During this time, holding the lash by both
ends of the
base strip, flex it back and forth forming the shape of a horseshoe.
This contours the base of the strip to fit easily and comfortably.
Center the lash close to the base of your natural lashes and press end into
place to secure it.
Features :
Keeps lashes securely in place.
Good stickness and dries invisibly.
Safe to use,easy to clear.
1.Clear white 2. Dries invisibly 3.Easy to clear
F-100 High Performance General Purpose Neutral Silicone Sealant(adhesive)
1.manufacture
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to marble, granite, brick, roof tile, stone, concrete, metal, aluminum board, plastic, door, window, road advertising, family decoration, glass curtain wall, etc.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 6 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to marble, granite, brick, roof tile, stone, concrete, metal, aluminum board, plastic, door, window, road advertising, family decoration, glass curtain wall, etc.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 6 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
F-101 High Performance Acid Silicone Sealant(adhesive)
1.manufacture
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Acid cure
Fast dry
Water proof
200ml/280ml/300ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to ceramic tile, ceramic, aluminum, stainless steel, non-oiled timber, glass, skylight, door, window, bathtub, wash-basin, water tap, pipe, bathroom, kitchen, storeroom, cold cellar, indoor fixing, etc.
Performance:
Acidity solidified; good weatherproof, like heatproof, waterproof, ice and snow resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 6 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for alkaline material, like concrete and cement; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Acid cure
Fast dry
Water proof
200ml/280ml/300ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to ceramic tile, ceramic, aluminum, stainless steel, non-oiled timber, glass, skylight, door, window, bathtub, wash-basin, water tap, pipe, bathroom, kitchen, storeroom, cold cellar, indoor fixing, etc.
Performance:
Acidity solidified; good weatherproof, like heatproof, waterproof, ice and snow resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 6 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for alkaline material, like concrete and cement; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
F-200 High Performance Neutral Silicone Sealant(adhesive)
1.manufacture
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to marble, granite, brick, roof tile, stone, concrete, metal, aluminum board, plastic, door, window, road advertising, family decoration, glass curtain wall, etc.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 9 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to marble, granite, brick, roof tile, stone, concrete, metal, aluminum board, plastic, door, window, road advertising, family decoration, glass curtain wall, etc.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 9 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2 Modified Epoxy Resin Injection ceramic adhesive for Planting Stud Bolt
1)Good bonding and strongly permeate
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
2)Non-volatile
3)Anti-aging and waterproof
4)Good toughness ,shock resistance
YC186 seam sealer is a kind of A, B groups modified epoxy resin adhesive with low viscosity liquid, its viscosity is low, less heat, ratio of liberal application for a long period use, serous perfusion technique
This product is widely used for repairing fissure in water conservancy, pavement concrete bridge, houses and other engineering, and repairing concrete ,if it cracks or loose,,FRP and structure surface anti-corrosive
.
Composition
A,B groups
proportion
A~B=2~1
Viscosity (cp,25c)
80
Density (g/cm3,25c)
1.0
Compressive (MPa)
51 (GB/T2569)
Flexural (MPa)
35 (GB/T2570)
Tensile (MPa)
23 (GB/T2568)
Note
Slight irritation to the skin
Package (barrel)
30kg/group(A~20kg. B~10kg)
F-201 High Performance Acid Silicone Sealant(adhesive)
1.manufacture
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Acid cure
Fast dry
Water proof
200ml/280ml/300ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to ceramic tile, ceramic, aluminum, stainless steel, non-oiled timber, glass, skylight, door, window, bathtub, wash-basin, water tap, pipe, bathroom, kitchen, storeroom, cold cellar, indoor fixing, etc.
Performance:
Acidity solidified; good weatherproof, like heatproof, waterproof, ice and snow resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 9 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for alkaline material, like concrete and cement; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Acid cure
Fast dry
Water proof
200ml/280ml/300ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to ceramic tile, ceramic, aluminum, stainless steel, non-oiled timber, glass, skylight, door, window, bathtub, wash-basin, water tap, pipe, bathroom, kitchen, storeroom, cold cellar, indoor fixing, etc.
Performance:
Acidity solidified; good weatherproof, like heatproof, waterproof, ice and snow resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 9 months from the date of produce.
Limitation:
Should not be used as structural sealant; not for cache or soaked underground joint; not for permanent or continuous water immersion; not for alkaline material, like concrete and cement; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
F-900 High Performance Structure Silicone Sealant(adhesive)
1.manufacture
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to glass, aluminum board, metal, stone, aluminum alloy; double glazing glass, concealed or semi-concealed frames; glass or metal combination, like aluminum and stainless steel.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 12 months from the date of produce.
Limitation:
Not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
2.excellent adhesive ability
3 good weatherproof
4.fast curing speed
5 rtv silicone
Neutral cure
Fast dry
Water proof
Weather proof
200ml/280ml/300ml/592ml
ISO 9002 International Quality & RoHS Certificated
Application:
Apply to glass, aluminum board, metal, stone, aluminum alloy; double glazing glass, concealed or semi-concealed frames; glass or metal combination, like aluminum and stainless steel.
Performance:
Neutral solidified, middle modulus; good weatherproof, like heatproof, ice and snow resistance, UV rays resistance, ozone resistant and extreme condition resistance; distinctive elasticity and restoring force; not easily influenced by weather or season; no harden or bursting occurred; no stimulus released; good bond strength and durable.
Usage:
Remove the impurities, clean and dry the surface, then cut the nozzle to a desired opening angle and apply the sealant with glue gun, press at 45 degrees. Normally cure on surface in 30 minutes and solidify in 24 to 48 hours.
Storage:
Store in the original airtight container and keep at cool, dry and well ventilated place with temperature at 20°C to 30°C, use within 12 months from the date of produce.
Limitation:
Not for cache or soaked underground joint; not for permanent or continuous water immersion; not for oily surface, like coating glass, mirror, coating metal, plastic, etc.
Caution:
If eye contacts to the uncured sealant, immediately flush with water for 15 minutes and consult doctor. Keep the job location ventilated. Keep out of reach of children.
FABRIC REPAIR GLUE
HOPSON High Temperature Silicone Gasket Maker is non-slumping, one component and acidic-curing rubber.
DESCRPTION:
Easy To Use Permanent Repair.
Permanent Repair.
Repairs Virtually Any Fabric.
Machine Washabel Up to 50 Washes.
Dries Crystal Clear& Safe For Most Surfaces.
MIGHTY MENDIT.
DESCRPTION:
Easy To Use Permanent Repair.
Permanent Repair.
Repairs Virtually Any Fabric.
Machine Washabel Up to 50 Washes.
Dries Crystal Clear& Safe For Most Surfaces.
MIGHTY MENDIT.
FAST DRY GLUE!!! BY-VF3000 Ethyl cyanoacrylate adhesive super glue Viscosity3000cps
1 for adhesion with woodwork/plastic/rubber
2 fast curing/quick dry
3 temperature resistance
4 3~5min cure
Company introduction:
BOYA CHEMICAL INTERNATIONAL COMPANY LIMTED is majoring in manufacturing and exporting Cyanoacrylate adhesive(502 super glue,nail glue and eyelash glue).We specialize in this field for 8 years.It is armed with advanced imported automatic equipment,
adopts advanced production technology, and established strict production and management systems. Our mission is "top quality, innovative product ,client primary and less waster."
Characteristics:
Chemical Type
Ethyl cyanoacrylate
Appearance(uncured)
Clear liquid
Components
One component
Viscosity
3000cps
Gap Fill
0.3mm
Setting Velocity
25sec
Shelf life
12month
Tensile-Shear Strength
100-150kgf/cm2
Directions for use
1
For best performance bond surfaces should be clean and free of grease.
2 This product performs best in this bond gaps (0.3mm).
3 Excess adhesive can be dissolved with cleanup solvents, nitromethane or acetone.
Storage
Store product in the unopened container in a dry location
Optimal Storage:
2~ 8°C
Note
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials
2 fast curing/quick dry
3 temperature resistance
4 3~5min cure
Company introduction:
BOYA CHEMICAL INTERNATIONAL COMPANY LIMTED is majoring in manufacturing and exporting Cyanoacrylate adhesive(502 super glue,nail glue and eyelash glue).We specialize in this field for 8 years.It is armed with advanced imported automatic equipment,
adopts advanced production technology, and established strict production and management systems. Our mission is "top quality, innovative product ,client primary and less waster."
Characteristics:
Chemical Type
Ethyl cyanoacrylate
Appearance(uncured)
Clear liquid
Components
One component
Viscosity
3000cps
Gap Fill
0.3mm
Setting Velocity
25sec
Shelf life
12month
Tensile-Shear Strength
100-150kgf/cm2
Directions for use
1
For best performance bond surfaces should be clean and free of grease.
2 This product performs best in this bond gaps (0.3mm).
3 Excess adhesive can be dissolved with cleanup solvents, nitromethane or acetone.
Storage
Store product in the unopened container in a dry location
Optimal Storage:
2~ 8°C
Note
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials
FD-13 spot welding sealant
It is used in weld seam.
Damping Expanding Adhesive
Specifications:
Item
Properties
Description
brown,paste,no impurities
Specific gravity g/cm3
1.3-1.5
Adhesive strength pa.s
1500-3500
Nonvolatile content %
≥97
Solid contend
170°c+/-2°c,30min
Package :
400g/tube, 380g/tube. or according to customers' requirement .carton
Damping Expanding Adhesive
Specifications:
Item
Properties
Description
brown,paste,no impurities
Specific gravity g/cm3
1.3-1.5
Adhesive strength pa.s
1500-3500
Nonvolatile content %
≥97
Solid contend
170°c+/-2°c,30min
Package :
400g/tube, 380g/tube. or according to customers' requirement .carton
FDN Water Reducing Admixture
High concentration super high effective water reducing admixture.
Main technica performance:
Item Index
Appearance Dark brown powder
Water reducing ratio 16%Min
Net cement grout flowability 225mm Min
PH value 8±1
Solid content 91±1
Sodium sulphate content 5%Max
Content of CI 0.5%Max
Scope of application:
Type 300-II water reducing admixture use widely applied into concrete projects,especiall adapting to the following:flowing concrete,plasticizing concrete,steam curing concrete,permeability resistant concrete,waterproofing concrete,mass concrete,natural curing precast concrete,reinforced concrete and pre stress concrete,green high strength high performance concrete and super high strength concrete.
USage:
Addition:The addition of type 300-II admixture is 0.4-1.0%,the general addition is 0.75%.When preparing low grade concrete or adopting slag cement or Portland pozzolana cement select and use the amount of 0.4-0.6%;while preparing high grade and pre srtessed concrete,select and use the amout of 0.75-1.0%.
Packing and storing:
1)Powder water reducing admixture type 300-II is 25Kg/bag,packed in plastic bag internally and in woven bag externally.
2)The powder admixture shall be kept in dry place with precaution against dampness.But the damped powder will not be affected on its effect,and can be used after proportioned to water solution.
Main technica performance:
Item Index
Appearance Dark brown powder
Water reducing ratio 16%Min
Net cement grout flowability 225mm Min
PH value 8±1
Solid content 91±1
Sodium sulphate content 5%Max
Content of CI 0.5%Max
Scope of application:
Type 300-II water reducing admixture use widely applied into concrete projects,especiall adapting to the following:flowing concrete,plasticizing concrete,steam curing concrete,permeability resistant concrete,waterproofing concrete,mass concrete,natural curing precast concrete,reinforced concrete and pre stress concrete,green high strength high performance concrete and super high strength concrete.
USage:
Addition:The addition of type 300-II admixture is 0.4-1.0%,the general addition is 0.75%.When preparing low grade concrete or adopting slag cement or Portland pozzolana cement select and use the amount of 0.4-0.6%;while preparing high grade and pre srtessed concrete,select and use the amout of 0.75-1.0%.
Packing and storing:
1)Powder water reducing admixture type 300-II is 25Kg/bag,packed in plastic bag internally and in woven bag externally.
2)The powder admixture shall be kept in dry place with precaution against dampness.But the damped powder will not be affected on its effect,and can be used after proportioned to water solution.
FLOOR ADHESIVE
one component polyurethane glue for laying various floor such as cork floor,solid foor and artificial floor,rubber floor,pvc
one component polyurethane glue for laying various floor such as cork floor,solid foor and artificial floor,rubber floor,pvc floor.
characterized by :
1.single componet ,easy to use
2.easy to repair in case it is broken
3.sound -proof and feel soft comfortable.
4.good bonding strength,especially for wood and concerte.
5.high efficiency
one component polyurethane glue for laying various floor such as cork floor,solid foor and artificial floor,rubber floor,pvc floor.
characterized by :
1.single componet ,easy to use
2.easy to repair in case it is broken
3.sound -proof and feel soft comfortable.
4.good bonding strength,especially for wood and concerte.
5.high efficiency
FOB Shanghai Port HDLL Polyacrylamide/PAM
PAM,
1.Flocculant in water treatment
2,Recycle Starch&Vinasse
3.Degreaser in oil field
4.Additives in papermaking
Polyacrylamide (PAM) is called flocculant poppularly, which has the molecular formular of +CH2-CHn, Linear polymers, molecular weight of 4,000,000—20,000,000, strong flocculation, easily soluble in water, dissolute above 120°C.
It appears white and light-yellow at solid, and colorless vicous colloid at liquid.
With this special structure, it can easily adsorb the suspended solids to purify the water thoroughly.
So it is widely used in metallurgy, papermaking, petroleum, chemical industry,
textiles and ore dressing for water treatment.
Anionic polyacrylamide specifications:
Item
C1610
C1620
C1635
C1650
Ion content
law
middle
middle
high
Molecular weight
(per 10 thousand)
1000-1200
1000-1200
800-1000
800-1000
Solid content
Min 90%
Min 90%
Min 90
Min 90%
Free Monomer
Max 0.05%
Max 0.05%
Max 0.05%
Max 0.05%
Dissolution time
Max 40
Max 40
Max 40
Max 40
It is widely used in:
1.metallurgy
2.papermaking
3.petroleum
4.chemical industry
5.textiles and ore dressing
1.Flocculant in water treatment
2,Recycle Starch&Vinasse
3.Degreaser in oil field
4.Additives in papermaking
Polyacrylamide (PAM) is called flocculant poppularly, which has the molecular formular of +CH2-CHn, Linear polymers, molecular weight of 4,000,000—20,000,000, strong flocculation, easily soluble in water, dissolute above 120°C.
It appears white and light-yellow at solid, and colorless vicous colloid at liquid.
With this special structure, it can easily adsorb the suspended solids to purify the water thoroughly.
So it is widely used in metallurgy, papermaking, petroleum, chemical industry,
textiles and ore dressing for water treatment.
Anionic polyacrylamide specifications:
Item
C1610
C1620
C1635
C1650
Ion content
law
middle
middle
high
Molecular weight
(per 10 thousand)
1000-1200
1000-1200
800-1000
800-1000
Solid content
Min 90%
Min 90%
Min 90
Min 90%
Free Monomer
Max 0.05%
Max 0.05%
Max 0.05%
Max 0.05%
Dissolution time
Max 40
Max 40
Max 40
Max 40
It is widely used in:
1.metallurgy
2.papermaking
3.petroleum
4.chemical industry
5.textiles and ore dressing
FS-III fast drying colloidal silica
FS-III fast-drying colloidal silica (silicon dioxide,silica sol)Particle size 8-20(nm),low impurity, high diaphaneity, etc.
FS-III fast-drying colloidal silica
FS-III type silicasol enhanced drying of the company is building following the FS- (FS-
30). FS-III type has a faster drying rate, but also Shell excellent performance, therefore more suitable for the use of precision casting industry. The product has been declared the national invention patent.however,if you are overseas,we strongly recommend FS-30 fast drying tpye beacause the FS-III only can be storaged for 3 months theoretically.
Main technical standards:
Designation
Standard
Appearance
Slight milky transparent to translucent
SiO
2
(wt%)
29±0.5%
Na
2
O (wt%)
≤0.5%
PH (20°C)
9.5-10.5
Density (20°C,g/cm
3
)
1.19-1.21
Viscosity (20°C,mPaS)
≤12
Particle size (nm)
8-20
Stability
≥3 months
Remark:
1.The using way is same with common colloidal silica.
2. The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
3.It only need about 1/3 time of common colloidal silica to dry.
4.The wind in shell making plant is most important.
5.Please park 24 hours before dewaxing.
6.It can replace ethyl orthosilicate, and its high-temp strength is higher.
7.It can replace the mixer of colloidal silica and latex.
8.It doesnt need to change using way.
9.The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
10.Because its wet strength is higher, its ability to resist dissolve is harder.
11.The wind in shell making plant is most important. About 1/2 time to dry for generic casts.
12.Its rudimental strength is lower, so its easier to clean.
13.Need 24 hours to park before dewaxing.
14.It can replace ethyl orthosilicate, and its high-temp strength is higher.
15.It can replace the mixer of colloidal silica and latex. But it cant be used with latex because of its special capability.
16.It doesnt need to change using way.
17.The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
18.Because its wet strength is higher, its ability to resist dissolve is harder.
19.The wind in shell making plant is most important. One or two hours are enough to dry for generic casts, when the wind speed is 8m/s in workshop.
20.Its rudimental strength is lower, so its easier to clean.
21.Need 24 hours to park before dewaxing.
22.It can replace ethyl orthosilicate, and its high-temp strength is higher.
23.It can replace the mixer of colloidal silica and latex. But it cant be used with latex because of its special capability.
Packing & Storage
Colloidal silica is packed in 25kg, 250kg or 1000kg plastic drums.
Store the colloidal silica at a temperature between 0 and 50, avoid exposure to the air, and insulate it from the sun.
Wash the empty drums as quickly as possible to avoid SiO
2
crystalline deposits.
If you want to remove the deposition from empty drums, use a 10-percent NaOH solution at 50~60.
FS-III fast-drying colloidal silica
FS-III type silicasol enhanced drying of the company is building following the FS- (FS-
30). FS-III type has a faster drying rate, but also Shell excellent performance, therefore more suitable for the use of precision casting industry. The product has been declared the national invention patent.however,if you are overseas,we strongly recommend FS-30 fast drying tpye beacause the FS-III only can be storaged for 3 months theoretically.
Main technical standards:
Designation
Standard
Appearance
Slight milky transparent to translucent
SiO
2
(wt%)
29±0.5%
Na
2
O (wt%)
≤0.5%
PH (20°C)
9.5-10.5
Density (20°C,g/cm
3
)
1.19-1.21
Viscosity (20°C,mPaS)
≤12
Particle size (nm)
8-20
Stability
≥3 months
Remark:
1.The using way is same with common colloidal silica.
2. The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
3.It only need about 1/3 time of common colloidal silica to dry.
4.The wind in shell making plant is most important.
5.Please park 24 hours before dewaxing.
6.It can replace ethyl orthosilicate, and its high-temp strength is higher.
7.It can replace the mixer of colloidal silica and latex.
8.It doesnt need to change using way.
9.The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
10.Because its wet strength is higher, its ability to resist dissolve is harder.
11.The wind in shell making plant is most important. About 1/2 time to dry for generic casts.
12.Its rudimental strength is lower, so its easier to clean.
13.Need 24 hours to park before dewaxing.
14.It can replace ethyl orthosilicate, and its high-temp strength is higher.
15.It can replace the mixer of colloidal silica and latex. But it cant be used with latex because of its special capability.
16.It doesnt need to change using way.
17.The life of slurry, the capability of coating and the high-temp strength are similar with common colloidal silica.
18.Because its wet strength is higher, its ability to resist dissolve is harder.
19.The wind in shell making plant is most important. One or two hours are enough to dry for generic casts, when the wind speed is 8m/s in workshop.
20.Its rudimental strength is lower, so its easier to clean.
21.Need 24 hours to park before dewaxing.
22.It can replace ethyl orthosilicate, and its high-temp strength is higher.
23.It can replace the mixer of colloidal silica and latex. But it cant be used with latex because of its special capability.
Packing & Storage
Colloidal silica is packed in 25kg, 250kg or 1000kg plastic drums.
Store the colloidal silica at a temperature between 0 and 50, avoid exposure to the air, and insulate it from the sun.
Wash the empty drums as quickly as possible to avoid SiO
2
crystalline deposits.
If you want to remove the deposition from empty drums, use a 10-percent NaOH solution at 50~60.
FUKKOL Repair Clay for Mould Repair
FUKKOL Repair Clay
- suitable for metal,wood,stone,plastic,ceramics and many other industry
- stone like after worked
FUKKOL Repair Clay
DESCRIPTION
FUKKOL Repair Clay
can apply to many area ,insulation of pipes and thanks,secu
ring of screws and hooks, renewing of taps, filling of uneven surfaces and holes and a thousand and one other uses.
MRTA-FILL works perfectly on metals, wood,stone,ceramics,plastic and glass .Can also be used and applied underwate
r.
EASY TO USE
The blue and the yellow substances should be worked together in a ratio of 1:1 until the resulting substance is totally green in color .Apply within 15 minutes.
Within 3 hours, META-FILL will be as hard as rock and can then be sanded,drilled,filed,sawn and threaded .Repairs effected by EMTA-FILL can be improved cosmeticaly by using a Metaflux Metal Spary or painted over
TECHNICAL DATA
Heat tolerance:Up to 200°C
Pressure resistance:8000 N/cm2
Tensile strength:3000 N/cm2
Hardening:3 hours at 20°C
Preparation time:15minutes
Specific gravity:2.0
Shelf life:At least 3 years if kept in closed container.
- suitable for metal,wood,stone,plastic,ceramics and many other industry
- stone like after worked
FUKKOL Repair Clay
DESCRIPTION
FUKKOL Repair Clay
can apply to many area ,insulation of pipes and thanks,secu
ring of screws and hooks, renewing of taps, filling of uneven surfaces and holes and a thousand and one other uses.
MRTA-FILL works perfectly on metals, wood,stone,ceramics,plastic and glass .Can also be used and applied underwate
r.
EASY TO USE
The blue and the yellow substances should be worked together in a ratio of 1:1 until the resulting substance is totally green in color .Apply within 15 minutes.
Within 3 hours, META-FILL will be as hard as rock and can then be sanded,drilled,filed,sawn and threaded .Repairs effected by EMTA-FILL can be improved cosmeticaly by using a Metaflux Metal Spary or painted over
TECHNICAL DATA
Heat tolerance:Up to 200°C
Pressure resistance:8000 N/cm2
Tensile strength:3000 N/cm2
Hardening:3 hours at 20°C
Preparation time:15minutes
Specific gravity:2.0
Shelf life:At least 3 years if kept in closed container.
Subscribe to:
Posts (Atom)