Moderate elasticity
Waterproofing
Paintable
No primer
Mildew proofing
Testing
Performance
Appearance
Black/White/Gray homogeneous paste
Density(g/cm3)
1.35±0.05
Sagging properties(mm)
0
Elongation at break(%)
≥600
Volatile content(%)
≤4
Stretch modulus (Mpa)
>0.4
Touch dry time(min)
≤180
Elastic recovery rate(%)
≥85
Extrudability (ml/min)
≥80
Pollution properties
Non
Application temperature(°C)
+5~+35
Shelf life(month)
9
Description:
KATER 521 Polyurethane Sealant is one component have excellent elasticity and adhesion strength, self bonding and easily for repairing etc.
Uses:
KATER521 Construction Polyurethane Sealant is for sealing tiles, cracks, sills, skylight, doors, various of marble, ceramic, glass metallic, wood, door, sanitary ware, tap fittings, roofing, wall penetrations, precast panels, and decorative tile lines.
§
APPLICATION:
Minimum application temperature: 5°C.
521 should be dispensed from either the cartridge or sausage by means of a caulking gun. Pierce the membrane at the top of the cartridge and screw on the nozzle. Cut nozzle to give the required angle and bead size. Place the cartridge in an applicator gun and squeeze the trigger. For sausages, a barrel gun is required, clip the end of the sausage and place in barrel gun. Screw end cap and nozzle on to barrel gun. Using the trigger extrude the sealant, to stop depress using the catch plate. Apply 521 in a continuous bead using enough pressure to properly fill the gaps.
Saturday, September 3, 2011
High Performance Acetic Silicone Sealant
fast curing speed
large binding power
excellent ageing-resistant performance
excellent adhesive
CHARACTERISTICS
FENGBA132 Acetic Silicone Sealant is in single component, acid, room curing, fast curing speed, large binding power, having excellent
ageing-resistant performance and excellent adhesive to most common building material. Which has little changes of performance at -40~150°C.
APPLICATION
Using in different kinds of engineering
Joint sealing to glass, marble and all kinds of glass door and window
Fit up automotive, ship, packaging advertisement and family decoration.
Use Method
1. Clean with solvents such as toluene or acetone to keep the substrate surfaces completely clean and dry;
2. For better appearance cover outside of joint areas with masking taps before application;
3. Cut nozzle to desired size and extrudes sealant to joint areas;
4. Tool immediately after sealant application and remove masking tape before sealant skins.
large binding power
excellent ageing-resistant performance
excellent adhesive
CHARACTERISTICS
FENGBA132 Acetic Silicone Sealant is in single component, acid, room curing, fast curing speed, large binding power, having excellent
ageing-resistant performance and excellent adhesive to most common building material. Which has little changes of performance at -40~150°C.
APPLICATION
Using in different kinds of engineering
Joint sealing to glass, marble and all kinds of glass door and window
Fit up automotive, ship, packaging advertisement and family decoration.
Use Method
1. Clean with solvents such as toluene or acetone to keep the substrate surfaces completely clean and dry;
2. For better appearance cover outside of joint areas with masking taps before application;
3. Cut nozzle to desired size and extrudes sealant to joint areas;
4. Tool immediately after sealant application and remove masking tape before sealant skins.
High Performance Acetic Silicone Sealant
one-part acetic
waterproof and outstanding weather resistant
Excellent adhesive to most common building material;
CHARACTERISTICS
FENGBA668 High Performance Acetic Silicone Sealant is one-part acetic silicone sealant. It is fast curing and permanently flexible, waterproof and outstanding weather resistant , Excellent adhesive to most common building material; The performance change less within the range between -50°C and 150°C.
APPLICATION
Bonding and sealing, aquaria glass, large plate glass, fish bowl, light roof glass members
Assembling door and window, transparent glass members
Bonding and sealing other kinds of glass assembling
waterproof and outstanding weather resistant
Excellent adhesive to most common building material;
CHARACTERISTICS
FENGBA668 High Performance Acetic Silicone Sealant is one-part acetic silicone sealant. It is fast curing and permanently flexible, waterproof and outstanding weather resistant , Excellent adhesive to most common building material; The performance change less within the range between -50°C and 150°C.
APPLICATION
Bonding and sealing, aquaria glass, large plate glass, fish bowl, light roof glass members
Assembling door and window, transparent glass members
Bonding and sealing other kinds of glass assembling
2011 hot sell edible taffee candy gelatine powder
Super Gelatin for Super Client
1.Cert: ISO ,QC, HACCP ,HALAL
2.Jelly Strength:70-280 bloom
3.Color: Pale yellow to White
We're specialized in gelatin with annal output 3000Ton/Year :
edible gelatin, technical gelatin pharmaceutical gelatin
:
1)Edible gelatin : jelly styrength 70-280Bloom
2)Technical gelatin : jelly strength 100-680Bloom
3)Pharmaceutical gelatin:jelly strength 130-280Bloom
Specifications:(for edible or pharma)
Production flow
1.Cert: ISO ,QC, HACCP ,HALAL
2.Jelly Strength:70-280 bloom
3.Color: Pale yellow to White
We're specialized in gelatin with annal output 3000Ton/Year :
edible gelatin, technical gelatin pharmaceutical gelatin
:
1)Edible gelatin : jelly styrength 70-280Bloom
2)Technical gelatin : jelly strength 100-680Bloom
3)Pharmaceutical gelatin:jelly strength 130-280Bloom
Specifications:(for edible or pharma)
Production flow
High Performance Electric & Thermal Conductive Interface Materials
Good thermal conductive: 10.0W/mK
Low thermal resistance
The High Performance Electric & Thermal Conductive Interface Materials of TIR™600-10 Series
products are high-performance and heat-conductive interface materials with the reasonable prices. They can be used in applications where no requirement for electric insulation is specified. The unique grain orientation and plate structure enable these products to adapt to different contact surfaces closely, and thus the maximized heat conduction function is attained.
Features
1.High thermal conductive of
10.0 W/mK
2.Low thermal resistance
Applications
1.Power conversion equipment
2.Power supplies
3.Large telecommunications switching hardware
4.Notebook computers
5.Led
Low thermal resistance
The High Performance Electric & Thermal Conductive Interface Materials of TIR™600-10 Series
products are high-performance and heat-conductive interface materials with the reasonable prices. They can be used in applications where no requirement for electric insulation is specified. The unique grain orientation and plate structure enable these products to adapt to different contact surfaces closely, and thus the maximized heat conduction function is attained.
Features
1.High thermal conductive of
10.0 W/mK
2.Low thermal resistance
Applications
1.Power conversion equipment
2.Power supplies
3.Large telecommunications switching hardware
4.Notebook computers
5.Led
High Performance Super Glue
I.Super glue
2.Liquid.
3.Instant bond in 3seconds
4.With high bonding strength.
I.Super glue is single-component cyanoacrylate monomer in liquid state
This instant super glue will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment.
Bond for home uses:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
SPECIFICATIONS:
Bonds in 3-5 Seconds
Validity: 1 year (20
o
C)
Material: Cyanoacrylate Adhesive
Gel content: ≥ 98%
Specific gravity: 1.06±0.02
Gap-fill(mm): 0.25-0.5
Model: fast bonding glue, instant glue, super glue
Shear strength: 7-16 MPa
Active use of phase: 0.05 min
Operating Temperature: around 25
o
C
Shelf life: 12 months
Standard of implementation: SGS MSDS
Warning: Keep out of reach of children:
2.Liquid.
3.Instant bond in 3seconds
4.With high bonding strength.
I.Super glue is single-component cyanoacrylate monomer in liquid state
This instant super glue will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment.
Bond for home uses:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
SPECIFICATIONS:
Bonds in 3-5 Seconds
Validity: 1 year (20
o
C)
Material: Cyanoacrylate Adhesive
Gel content: ≥ 98%
Specific gravity: 1.06±0.02
Gap-fill(mm): 0.25-0.5
Model: fast bonding glue, instant glue, super glue
Shear strength: 7-16 MPa
Active use of phase: 0.05 min
Operating Temperature: around 25
o
C
Shelf life: 12 months
Standard of implementation: SGS MSDS
Warning: Keep out of reach of children:
High Performance Weatherproofing Silicone Sealant OLV4800
1,High performance weatherproof
2,seal curtain wall,facade,rubber,other general purpose glazing
3,excellent weather resistant
Description:
High Performance Weatherproofing Silicone Sealant OLV4800 is a one-component neutral curing silicone sealant with excellent adhesion, weatherability and elasticity for weather sealing in curtain wall and building facades, especially suits applications in the areas with large difference in temperature and low humidity. It easily extrudes in any weather and quickly cures at room temperature by reaction with moisture in the air to form a durable silicone rubber seal.
Main purposes:
1. For weatherproofing sealing nonstructural curtain wall joints, facade joints and system;
2. Weather sealing in metal (not including copper), glass, stone, aluminium panel, and plastic;
3. Excellent adhesion to most common building material.
Characteristics:
1. One-component, neutral-cured with excellent adhesion, weatherability and elasticity for weather sealing in curtainwall and building facades;
2. Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes;
3. With good adhesion and compatibility with most building material;
4. Remain flexible over a temperature range of -40
0
C to 150
0
C.
Application:
1. Clean with solvents such as toluene or acetone to keep the substrate surfaces completely clean and dry;
2. For better appearance cover outside of joint areas with masking taps before application;
3. Cut nozzle to desired size and extrudes sealant to joint areas;
4. Tool immediately after sealant application and remove masking tape before sealant skins.
Limitations:
1. Unsuitable for curtain wall structural adhesive;
2. Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
3. Unsuitable for the frosty or moist surface;
4. Unsuitable for the continually soggy place;
5. Cant be used if the temperature is below 4°C or above 50°C on the surface of the material.
Shelf life: 9 months if keep sealing, and stored below 27
0
C in cool, dry place after the date of production.
Standard: I 25HM JC/T 882-2001
Volume: 300ml
Technical data:
The following data are only for reference purpose, not intended for use in preparing specification.
High Performance Weatherproofing Silicone Sealant OLV4800
Performance
Standard
Measured Value
Testing Method
Test at 50±5% RH and temperature 23±2
0
C:
Density (g/cm
3
)
±0.1
1.41
GB/T 13477
Tack-Free Time (min)
≤180
40
GB/T 13477
Extrusion (ml/min)
≥80
234
GB/T 13477
Tensile Modulus (Mpa)
23
0
C
0.4
0.63
GB/T 13477
20
0
C
or 0.6
/
Slumpability (mm) vertical
not change shape
not change shape
GB/T 13477
Slumpability (mm) horizontal
≤3
0
GB/T 13477
Curing Speed (mm/d)
2
3
/
As Cured -After 21 days at 50±5% RH and temperature 23±2
0
C:
Hardness (Shore A)
20~60
45
GB/T 531
Tensile Strength under Standard Conditions (Mpa)
/
0.83
GB/T 13477
Elongation of Rupture (%)
/
297
GB/T 13477
Movement Capability (%)
25
25
GB/T 13477
Storage
9 Months
2,seal curtain wall,facade,rubber,other general purpose glazing
3,excellent weather resistant
Description:
High Performance Weatherproofing Silicone Sealant OLV4800 is a one-component neutral curing silicone sealant with excellent adhesion, weatherability and elasticity for weather sealing in curtain wall and building facades, especially suits applications in the areas with large difference in temperature and low humidity. It easily extrudes in any weather and quickly cures at room temperature by reaction with moisture in the air to form a durable silicone rubber seal.
Main purposes:
1. For weatherproofing sealing nonstructural curtain wall joints, facade joints and system;
2. Weather sealing in metal (not including copper), glass, stone, aluminium panel, and plastic;
3. Excellent adhesion to most common building material.
Characteristics:
1. One-component, neutral-cured with excellent adhesion, weatherability and elasticity for weather sealing in curtainwall and building facades;
2. Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes;
3. With good adhesion and compatibility with most building material;
4. Remain flexible over a temperature range of -40
0
C to 150
0
C.
Application:
1. Clean with solvents such as toluene or acetone to keep the substrate surfaces completely clean and dry;
2. For better appearance cover outside of joint areas with masking taps before application;
3. Cut nozzle to desired size and extrudes sealant to joint areas;
4. Tool immediately after sealant application and remove masking tape before sealant skins.
Limitations:
1. Unsuitable for curtain wall structural adhesive;
2. Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
3. Unsuitable for the frosty or moist surface;
4. Unsuitable for the continually soggy place;
5. Cant be used if the temperature is below 4°C or above 50°C on the surface of the material.
Shelf life: 9 months if keep sealing, and stored below 27
0
C in cool, dry place after the date of production.
Standard: I 25HM JC/T 882-2001
Volume: 300ml
Technical data:
The following data are only for reference purpose, not intended for use in preparing specification.
High Performance Weatherproofing Silicone Sealant OLV4800
Performance
Standard
Measured Value
Testing Method
Test at 50±5% RH and temperature 23±2
0
C:
Density (g/cm
3
)
±0.1
1.41
GB/T 13477
Tack-Free Time (min)
≤180
40
GB/T 13477
Extrusion (ml/min)
≥80
234
GB/T 13477
Tensile Modulus (Mpa)
23
0
C
0.4
0.63
GB/T 13477
20
0
C
or 0.6
/
Slumpability (mm) vertical
not change shape
not change shape
GB/T 13477
Slumpability (mm) horizontal
≤3
0
GB/T 13477
Curing Speed (mm/d)
2
3
/
As Cured -After 21 days at 50±5% RH and temperature 23±2
0
C:
Hardness (Shore A)
20~60
45
GB/T 531
Tensile Strength under Standard Conditions (Mpa)
/
0.83
GB/T 13477
Elongation of Rupture (%)
/
297
GB/T 13477
Movement Capability (%)
25
25
GB/T 13477
Storage
9 Months
High Performance silicone sealant
High Performance Silicone Sealant
1.Acetoxy silicone sealant
2.high performance, with excellent adhesion to most material.
DESCRIPTION
SS621 Silicone Structural Glazing Sealant is a one-component, high strength neutral curing silicone sealant designed and tested for structurally glazed curtain wall applications. The material is supplied as a paste, which cures into an extremely tough elastomeric silicone rubber ensuring a durable, flexible, watertight bond upon exposure to atmospheric moisture.
CHARACTERISTICS
High strength and high elongation.
Odorless, non-corrosive cure system.
Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes.
Remains flexible over a temperature range of -55°F (-48°C) to 250°F (121°C).
Successfully tested for use in protective glazing applications.
Excellent unprimed adhesion to wide range of substrates including coated, enameled and reflective glasses, anodized and polyester coated or painted aluminum profiles including most fluoropolymerbased paints.
Good compatibility with other neutral silicone sealants.
Meets global standards for structural glazing (American, China, Europe).
APPLICATIONS
Silicone structural glazing in curtain wall; such as factory glazing of unitized curtain wall systems or in field constructed stick curtain wall systems.
Structural attachment of many panel systems.
Protective glazing applications.
Panel stiffener applications.
1.Acetoxy silicone sealant
2.high performance, with excellent adhesion to most material.
DESCRIPTION
SS621 Silicone Structural Glazing Sealant is a one-component, high strength neutral curing silicone sealant designed and tested for structurally glazed curtain wall applications. The material is supplied as a paste, which cures into an extremely tough elastomeric silicone rubber ensuring a durable, flexible, watertight bond upon exposure to atmospheric moisture.
CHARACTERISTICS
High strength and high elongation.
Odorless, non-corrosive cure system.
Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes.
Remains flexible over a temperature range of -55°F (-48°C) to 250°F (121°C).
Successfully tested for use in protective glazing applications.
Excellent unprimed adhesion to wide range of substrates including coated, enameled and reflective glasses, anodized and polyester coated or painted aluminum profiles including most fluoropolymerbased paints.
Good compatibility with other neutral silicone sealants.
Meets global standards for structural glazing (American, China, Europe).
APPLICATIONS
Silicone structural glazing in curtain wall; such as factory glazing of unitized curtain wall systems or in field constructed stick curtain wall systems.
Structural attachment of many panel systems.
Protective glazing applications.
Panel stiffener applications.
High Quality Siliconized Acrylic Sealant Caulk
YA4000 siliconized acrylic caulking remains flexible over a wide range of temperature.
YA4000
High quality siliconized acrylic caulk is a good choice for many interior or exterior painting projects. This caulking remains flexible over a wide range of temperatures. Making it suitable for
exterior caulking
applications, such as sealing around windows or doors and gaps between fascia boards or siding.
Generally interior surfaces remain stable, producing less movement, but
interior caulking
still requires a good sealant. YA4000 Siliconized acrylic sealants have become the standard painters caulk, able to adhere to a wide range of materials. Plus is fully paintable with acrylic or alkyd paints when fully cured.
Features and Benefits
YA4000is an easy gunning, non-staining, general purpose sealant formulated from the highest quality acrylic polymer to offer exceptional flexibility and workability for any commercial construction acrylic sealant application. It can be used indoors or outside, and is tack-free in 15 minutes and ready to paint in 30-45 minutes with latexes or oil-based paint. It also has been tested for acoustical properties to reduce sound transmissions when constructing partition partition walls.
Basic Uses
YA4000 can be used for general purpose interior and exterior caulking and as a back bedding glazing compound. It is also highly recommended as an acoustical seal in the construction of interior walls, ceiling and floors. It is also suitable for use on vinyl, aluminum and wood siding as well as on bathroom and fixtures.
Colors
White, Limestone, Black, Cream, Almond Cream, Eggshell cream, Cedar, Beige Gray, Mortar and Lava.
Packaging
10.1oz
(300ml cartridges
Bulk by drum: 200lt
Coverage Rate
35 linear feet of joint per 10.1oz (300ml)cartridge for a 1/4”x 1/4” joint. For specific coverage rates that include joint size, and usage efficiencies.
Applicable Standards
YA4000meets or exceeds the requirements of the following specifications:
1.STM C-834,Type OP, Grade- 18°C
2.AN/CGSB 19-GP-17M
Dry Time
At 72°F(22°C),50% R.H., YA4000 is tack free in 15 minutes and drieds at a rate of about 1/8” per day but can be painted after only 30 to 45 minutes with latexes,or oil-based paint.As the temperatures decrease,the dry time of YA40000 will increase.A good rule of thumb is one additional day for every 10°F decrease in temperature.
YA4000
High quality siliconized acrylic caulk is a good choice for many interior or exterior painting projects. This caulking remains flexible over a wide range of temperatures. Making it suitable for
exterior caulking
applications, such as sealing around windows or doors and gaps between fascia boards or siding.
Generally interior surfaces remain stable, producing less movement, but
interior caulking
still requires a good sealant. YA4000 Siliconized acrylic sealants have become the standard painters caulk, able to adhere to a wide range of materials. Plus is fully paintable with acrylic or alkyd paints when fully cured.
Features and Benefits
YA4000is an easy gunning, non-staining, general purpose sealant formulated from the highest quality acrylic polymer to offer exceptional flexibility and workability for any commercial construction acrylic sealant application. It can be used indoors or outside, and is tack-free in 15 minutes and ready to paint in 30-45 minutes with latexes or oil-based paint. It also has been tested for acoustical properties to reduce sound transmissions when constructing partition partition walls.
Basic Uses
YA4000 can be used for general purpose interior and exterior caulking and as a back bedding glazing compound. It is also highly recommended as an acoustical seal in the construction of interior walls, ceiling and floors. It is also suitable for use on vinyl, aluminum and wood siding as well as on bathroom and fixtures.
Colors
White, Limestone, Black, Cream, Almond Cream, Eggshell cream, Cedar, Beige Gray, Mortar and Lava.
Packaging
10.1oz
(300ml cartridges
Bulk by drum: 200lt
Coverage Rate
35 linear feet of joint per 10.1oz (300ml)cartridge for a 1/4”x 1/4” joint. For specific coverage rates that include joint size, and usage efficiencies.
Applicable Standards
YA4000meets or exceeds the requirements of the following specifications:
1.STM C-834,Type OP, Grade- 18°C
2.AN/CGSB 19-GP-17M
Dry Time
At 72°F(22°C),50% R.H., YA4000 is tack free in 15 minutes and drieds at a rate of about 1/8” per day but can be painted after only 30 to 45 minutes with latexes,or oil-based paint.As the temperatures decrease,the dry time of YA40000 will increase.A good rule of thumb is one additional day for every 10°F decrease in temperature.
High Quality Adhesives(Animal Glue)
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover , book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover , book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Animal Glue for case making
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover ,book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
6 months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover ,book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
6 months
High Quality Animal Glue for hard book cover
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Animal Glue
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Clear Acrylic Sealant Caulk
YA9000 is a one-component, high-performance, elastomeric sealant with the permanent adhesion and UV resistant properties
YA9000 is a
one-component, high-performance, elastomeric sealant with the permanent adhesion and UV resistant properties of acrylic plus the permanent flexibility and lifetime durability of silicone. A high quality caulk will not crack, crumble or peel, even when exposed to severe weather or total joint movement; for interior or exterior use.
BASIC USES:
YA9000 ULTRA CLEAR CAULK provides a waterproof and weatherproof seal, adhering tightly to interior and exterior surfaces, even to ceramic and glass substraters. Excellent for siding corner joints and caulking around windows, doors, skylights, vents, air ducts and chimneys.
PRODUCT ADVANTAGES:
*Interior / exterior
*40-year warranty
*Non-yellowing
*Seals in concrete, drywall, wood and metal
*100% odor free
*100% flexible
*100% silicone durability
*100% clear
*Mildew and moisture resistant
No
Item
YA9000
1
Colour
Translucent
2
Specific gravity, g/cm3
1.2
3
Shrinkage(mm)
≤3
4
Tack free time, h
0.7
5
Elongation at break,%
150
6
Modulus adhesive
OK
7
Volume Change,%
40
8
Extrudability, ml/min
495
9
Elastic Recovery Ratio,%
80
10
Hypothermia Flexibility, °C
-20
11
Viscosity cps
195000
Note:YA9000 ULTRA CLEAR CAULK guns out white but will dry clear; maximum clarity after thirteen days.
YA9000 is a
one-component, high-performance, elastomeric sealant with the permanent adhesion and UV resistant properties of acrylic plus the permanent flexibility and lifetime durability of silicone. A high quality caulk will not crack, crumble or peel, even when exposed to severe weather or total joint movement; for interior or exterior use.
BASIC USES:
YA9000 ULTRA CLEAR CAULK provides a waterproof and weatherproof seal, adhering tightly to interior and exterior surfaces, even to ceramic and glass substraters. Excellent for siding corner joints and caulking around windows, doors, skylights, vents, air ducts and chimneys.
PRODUCT ADVANTAGES:
*Interior / exterior
*40-year warranty
*Non-yellowing
*Seals in concrete, drywall, wood and metal
*100% odor free
*100% flexible
*100% silicone durability
*100% clear
*Mildew and moisture resistant
No
Item
YA9000
1
Colour
Translucent
2
Specific gravity, g/cm3
1.2
3
Shrinkage(mm)
≤3
4
Tack free time, h
0.7
5
Elongation at break,%
150
6
Modulus adhesive
OK
7
Volume Change,%
40
8
Extrudability, ml/min
495
9
Elastic Recovery Ratio,%
80
10
Hypothermia Flexibility, °C
-20
11
Viscosity cps
195000
Note:YA9000 ULTRA CLEAR CAULK guns out white but will dry clear; maximum clarity after thirteen days.
002 top Carbon fiber adhesives
1.this adhesion two components with epoxy resin
2.be heat-insulation .low viscosity
3.anti-aging waterproof good tenacity...
YC189 carbon fiber adhesion be made of rear adhesive , leveling rubber,
impregnated paste adhesive composition. At the end of the bottom surface
of building for the reinforcement leveling the surface of components for repairing ,
apply to carbon fiber, glass fiber and other fiber sheet In the concrete,
masonry and wood structures bonding with carbon fiber, mainly used in
the reinforcement on the resistance of tensile,
Construction procedure
Concrete surface treatment → rear construction → leveling construction → paste CFRP → curing conservation → test
2.be heat-insulation .low viscosity
3.anti-aging waterproof good tenacity...
YC189 carbon fiber adhesion be made of rear adhesive , leveling rubber,
impregnated paste adhesive composition. At the end of the bottom surface
of building for the reinforcement leveling the surface of components for repairing ,
apply to carbon fiber, glass fiber and other fiber sheet In the concrete,
masonry and wood structures bonding with carbon fiber, mainly used in
the reinforcement on the resistance of tensile,
Construction procedure
Concrete surface treatment → rear construction → leveling construction → paste CFRP → curing conservation → test
2011 newest ZQ451 Organosilicone sealant
ZQ451 red temperature silicone adhesive sealant
ZQ451 red temperature silicone adhesive sealant, a variety of viscosity specifications.
Its salient features are: has excellent temperature resistance, -60 ~ 280 °C in the range of long-term use.
Also has good adhesion, moisture, shock, corona resistant, anti-leakage and anti-aging properties, are widely used for high temperature bonding and sealing components, is de-oxime single-component room temperature curing silicone rubber
does not apply to copper and polycarbonate (PC) adhesive potting material, in line with the EU ROHS directive. .
ZQ451 red temperature silicone adhesive sealant, a variety of viscosity specifications.
Its salient features are: has excellent temperature resistance, -60 ~ 280 °C in the range of long-term use.
Also has good adhesion, moisture, shock, corona resistant, anti-leakage and anti-aging properties, are widely used for high temperature bonding and sealing components, is de-oxime single-component room temperature curing silicone rubber
does not apply to copper and polycarbonate (PC) adhesive potting material, in line with the EU ROHS directive. .
High Quality Gel Glue(Protein based Adhesives)
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover ,book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover ,book cover etc.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CARTHEM, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Grade Hot Melt Adhesive
Hot Melt adhesive
1.Shape:block 500g each piece
2.Strong Peeling
3.Low temperature in use:120-140 degree
4.Easy melt
Baby Diapers Hot Melt Adhesive
1.Feature:
strong Peeling strength, excellent anti-aging properties, good Elasticity, low temperature in use and energy saving, avoid the problem of adhesive carbonization due to high temperature.
2.Application:
Low temperature construction adhesive used on baby diapers or sanitary napkin
.
3.Technical data:
Properties
Specification value
Test Method and equipment
Shape
Light yellow in block or pillow shaped package
Visual
Solid Content
100%
Base
High polymer
Soften Point
75±5°C
GB/T 15332
Softening point tester
Viscosity
1500±300CPS at140°C; 1000±300CPS at150°C; 700±150CPS at160°C
SNB-2 Digital Rotational Viscometer, 27# rotor test
Recommend working temperature
120-140°C
usage
Low temperature construction adhesive used on the baby diaper and Women sanitary napkin.
4.Storage period:
2 Years (indoor, unexposed to the sunlight, not more than 40 degree)
5. Method for clearing equipment:
You can consult to the equipment manufacturer, or clean the equipment by clean mineral oil at 120 degree.After clean-up, flush it by the same hot melt adhesive not more than degree.
6.Safety Precautions:
To Minimize the risk of burns, please wear protective clothing & Goggles when working near the glue machine/applicator.To minimize the danger of Flammable vapors, the temperature should be lower than 180degree . Prevent the built-up of vapors, extinguish all sources of ignition during the use of hot melt.
1.Shape:block 500g each piece
2.Strong Peeling
3.Low temperature in use:120-140 degree
4.Easy melt
Baby Diapers Hot Melt Adhesive
1.Feature:
strong Peeling strength, excellent anti-aging properties, good Elasticity, low temperature in use and energy saving, avoid the problem of adhesive carbonization due to high temperature.
2.Application:
Low temperature construction adhesive used on baby diapers or sanitary napkin
.
3.Technical data:
Properties
Specification value
Test Method and equipment
Shape
Light yellow in block or pillow shaped package
Visual
Solid Content
100%
Base
High polymer
Soften Point
75±5°C
GB/T 15332
Softening point tester
Viscosity
1500±300CPS at140°C; 1000±300CPS at150°C; 700±150CPS at160°C
SNB-2 Digital Rotational Viscometer, 27# rotor test
Recommend working temperature
120-140°C
usage
Low temperature construction adhesive used on the baby diaper and Women sanitary napkin.
4.Storage period:
2 Years (indoor, unexposed to the sunlight, not more than 40 degree)
5. Method for clearing equipment:
You can consult to the equipment manufacturer, or clean the equipment by clean mineral oil at 120 degree.After clean-up, flush it by the same hot melt adhesive not more than degree.
6.Safety Precautions:
To Minimize the risk of burns, please wear protective clothing & Goggles when working near the glue machine/applicator.To minimize the danger of Flammable vapors, the temperature should be lower than 180degree . Prevent the built-up of vapors, extinguish all sources of ignition during the use of hot melt.
High Quality Industrial Adhesives(Animal Glue)
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Jelly Glue
SGS Certificate
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
MSDS
ISO9001:2000
Stable Quality
Competitive price
*Adhesive (Jelly Glue,protein based glue,cake glue,animal glue)for book binding,casemaking*
Application
:
Used in hard cover binding book(case-making) & paper box making. (Folder Cover,Album Cover etc book cover.)
Machine
It is suitable for the machineries of KOLBUS, STAHL, HORAUF, CRATHERN, EMMCI, PERONDI, POTDEVIN, Purple Magna, FuZhong & RuiAnZhongKe, and other kinds of case making machine, hard cover binding line; meanwhile, it is also suitable for hand-making.
Certificate:
SGS test report, ISO9001:2000 Quality Management Systems, China Supervision&Inspection Center test report
Packaging:
25kg
/carton
Shelf life:
Six months
High Quality Polyvinyl Alcohol
High Quality Polyvinyl Alcohol
1)PVA17-88, white powder or Granular.
2)Easy to soluble in water and has good viscosity.
PVA Product Characteristics and Instruction
1.Product Performance
Polymer is a kind of high polymer. It is white or light yellow floc, Granular or powdery in appearance. Its molecular formula is[CH2CHOH]n,and the molecular formula for some of the PVA is -[CH2CHOH]n-[CH2CHOOCCH3]m-. PVA is non-toxic, insipid and harmless. PVA is water-soluble and the solvent provide good viscosity and film building. It can withstand oils, lubricants, hydrocarbons and most other organic solvents. PVA has better chemical stability and insulatibility, and provide ease in firm building; It possess the typical chemical properties of polyols and can carry out process of esterification, etherealization, aceatalization etc.
2.Product Use
a.textile industry:PVOH is mainly used as a warp dressing agent, textile finishing agent and the raw material of vinylon;
b.construction :upholstery industry 107 glue, it's used as an additive of cement and mortar, inner and outer wall paints, and moulding board binder
c.chemical industry: it's used as a polymer emulsifying agent, dispersing agent and used to produce PVOH formal, PVOH acetal and PVOH butyral.
d.paper industry:It's used as an adhesive in lumbering and paper-making industries.
e. agriculture: used as a soil improving agent, pesticide reinforcing agent and PVOH thin film
f. used as a well-fixing agent in petroleum exploitation.
g. It can also be used into cosmetic, medicine, printing, ceramics, steel-making, electronics and plating.
3.Dissolving Temperature, thickness and time
PVA products dissolvent ability is determined by the degree of alcoholysis and polymerization. When polymerization increased, the ability to dissolve will reduced. Likewise, when the degree of alcoholysis decreased, the dissolvent temperature will reduced and water solubility will increase. Fully alcoholysed PVA products are more sensitive to temperatures changes. Such products cannot dissolve or experience partial swell in properties when temperature falls below required degree. Blending will be difficult and foam created should the temperature exceed the required degree for partial alcoholysis products. Temperature must be controlled at acceptable range for ease of dissolving.
Product Name
Alcoholysis degree(mol/mol)
Viscosity(mPa.s)
sodium acetate(≤)
Volatile constituen(≤)
Ash content(≤)
PH value
HWE1799
≥99.8
20.0-32.0
7.0
8.0
3.0
7-10
HWE2499
≥99.8
55.0-65.0
7.0
8.0
3.0
7-10
HWE2099
≥99.8
32.0-42.0
7.0
8.0
3.0
7-10
HWE0588
86.0-90.0
4.0-6.0
1.5
4
0.5
5-7
HWE1788
86.0-90.0
20.0-26.0
1.5
4
0.5
5-7
HWE1799
98.0-100
21.0-31.0
1.5
4
0.7
5-7
HWE2088
86.0-90.0
27.0-34.0
1.5
4
0.5
5-7
HWE2099
98.0-100
35.0-44.0
1.5
4
0.7
5-7
HWE2488
86.0-90.0
44.0-50.0
1.5
4
0.5
5-7
HWE2497
96.0-98.0
52.0-60.0
1.5
4
0.7
5-7
HWE2499
98.0-100
55.0-64.0
1.5
4
0.7
5-7
HWE2688
86.0-90.0
50.0-58.0
1.5
4
0.5
5-7
HWE2699
98.0-100
64.0-70.0
1.5
4
0.7
5-7
1)PVA17-88, white powder or Granular.
2)Easy to soluble in water and has good viscosity.
PVA Product Characteristics and Instruction
1.Product Performance
Polymer is a kind of high polymer. It is white or light yellow floc, Granular or powdery in appearance. Its molecular formula is[CH2CHOH]n,and the molecular formula for some of the PVA is -[CH2CHOH]n-[CH2CHOOCCH3]m-. PVA is non-toxic, insipid and harmless. PVA is water-soluble and the solvent provide good viscosity and film building. It can withstand oils, lubricants, hydrocarbons and most other organic solvents. PVA has better chemical stability and insulatibility, and provide ease in firm building; It possess the typical chemical properties of polyols and can carry out process of esterification, etherealization, aceatalization etc.
2.Product Use
a.textile industry:PVOH is mainly used as a warp dressing agent, textile finishing agent and the raw material of vinylon;
b.construction :upholstery industry 107 glue, it's used as an additive of cement and mortar, inner and outer wall paints, and moulding board binder
c.chemical industry: it's used as a polymer emulsifying agent, dispersing agent and used to produce PVOH formal, PVOH acetal and PVOH butyral.
d.paper industry:It's used as an adhesive in lumbering and paper-making industries.
e. agriculture: used as a soil improving agent, pesticide reinforcing agent and PVOH thin film
f. used as a well-fixing agent in petroleum exploitation.
g. It can also be used into cosmetic, medicine, printing, ceramics, steel-making, electronics and plating.
3.Dissolving Temperature, thickness and time
PVA products dissolvent ability is determined by the degree of alcoholysis and polymerization. When polymerization increased, the ability to dissolve will reduced. Likewise, when the degree of alcoholysis decreased, the dissolvent temperature will reduced and water solubility will increase. Fully alcoholysed PVA products are more sensitive to temperatures changes. Such products cannot dissolve or experience partial swell in properties when temperature falls below required degree. Blending will be difficult and foam created should the temperature exceed the required degree for partial alcoholysis products. Temperature must be controlled at acceptable range for ease of dissolving.
Product Name
Alcoholysis degree(mol/mol)
Viscosity(mPa.s)
sodium acetate(≤)
Volatile constituen(≤)
Ash content(≤)
PH value
HWE1799
≥99.8
20.0-32.0
7.0
8.0
3.0
7-10
HWE2499
≥99.8
55.0-65.0
7.0
8.0
3.0
7-10
HWE2099
≥99.8
32.0-42.0
7.0
8.0
3.0
7-10
HWE0588
86.0-90.0
4.0-6.0
1.5
4
0.5
5-7
HWE1788
86.0-90.0
20.0-26.0
1.5
4
0.5
5-7
HWE1799
98.0-100
21.0-31.0
1.5
4
0.7
5-7
HWE2088
86.0-90.0
27.0-34.0
1.5
4
0.5
5-7
HWE2099
98.0-100
35.0-44.0
1.5
4
0.7
5-7
HWE2488
86.0-90.0
44.0-50.0
1.5
4
0.5
5-7
HWE2497
96.0-98.0
52.0-60.0
1.5
4
0.7
5-7
HWE2499
98.0-100
55.0-64.0
1.5
4
0.7
5-7
HWE2688
86.0-90.0
50.0-58.0
1.5
4
0.5
5-7
HWE2699
98.0-100
64.0-70.0
1.5
4
0.7
5-7
High Quality Strong Viscosity Neutral Silicone Sealant
1.Strong Viscosity, High Quality & Non Corrosive
2.Applicable to Glasses, Aluminum Alloy Windows & Kitchen Outfits
Product Details:
1. A single-component quick dry sealant for joint sealing of various kinds of glasses, aluminum alloy door/window, kitchen outfits, bathroom articles and metal curtain wall, etc.
2. No base coating is needed in general when it is used to stick with building material.
3. An excellent resistant of being weathered such as raining. It is resistant to water, ultraviolet and ozone, etc.
4. Multiple color of choice is avaliable.
General Specification:
1. Time of Surface Curing - less than 30 mins in 25°C
2. Time of Total Curing - less than 24 hrs in 25°C
3. Drooping in Horizontal Level - Not distorted / in Upright Level - 0 (mm)
4. Extrusion Speed - 155 (ml/min)
2.Applicable to Glasses, Aluminum Alloy Windows & Kitchen Outfits
Product Details:
1. A single-component quick dry sealant for joint sealing of various kinds of glasses, aluminum alloy door/window, kitchen outfits, bathroom articles and metal curtain wall, etc.
2. No base coating is needed in general when it is used to stick with building material.
3. An excellent resistant of being weathered such as raining. It is resistant to water, ultraviolet and ozone, etc.
4. Multiple color of choice is avaliable.
General Specification:
1. Time of Surface Curing - less than 30 mins in 25°C
2. Time of Total Curing - less than 24 hrs in 25°C
3. Drooping in Horizontal Level - Not distorted / in Upright Level - 0 (mm)
4. Extrusion Speed - 155 (ml/min)
High Quality Strong Viscosity Wallpaper Glue
1.Strong Viscosity, High Quality, Odorless and Earth Friendly
2.Applicable to all kinds of wallpaper
3.Easily to use
Adhesive Glue Powder
Product Detail:
1. Net Weight - 180(g)
2. Made by high quality of starch with strong viscosity and high resistance to mold and water
3. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
4. Qualified for GB 18583-2001
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.01 (g/kg)
2. Concentration of Benzene - less than 0.01 (g/kg)
3. Concentration of Toluene and Dimethylbenzene - less than 0.01 (g/kg)
4. Concentration of Volatile Organic Compounds (VOC) - 2 (g/kg)
Wallpaper Adhesive
Product Detail:
1. Net Weight - 400(g)
2. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
3. Qualified for GB 18583-2008
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.2 (g/kg)
2.Applicable to all kinds of wallpaper
3.Easily to use
Adhesive Glue Powder
Product Detail:
1. Net Weight - 180(g)
2. Made by high quality of starch with strong viscosity and high resistance to mold and water
3. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
4. Qualified for GB 18583-2001
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.01 (g/kg)
2. Concentration of Benzene - less than 0.01 (g/kg)
3. Concentration of Toluene and Dimethylbenzene - less than 0.01 (g/kg)
4. Concentration of Volatile Organic Compounds (VOC) - 2 (g/kg)
Wallpaper Adhesive
Product Detail:
1. Net Weight - 400(g)
2. Excellent performance in all kinds of wallpaper, especially the ones made by heavy and embossed papers.
3. Qualified for GB 18583-2008
General Speicification:
1. Concentration of Free Formaldehyde - less than 0.2 (g/kg)
High Quality Super Glue Gel
super glue gel for industrial range ,long lasting.Fast bonding,convenient usage,high strength,no toxicity,non flammable,
SUPER GLUE GEL 401 ,495 ,406, 416,498 are mades srom cyamoacrylate adhesive,For industrial range ,wood ,rubber,plastics,metal,paper &leather.
APPLICATION:Be sure both surfaces are clean and dry.Apply with extreme care .Never spread with fingers.Apply to only one of the surface,Quickly place two surfaces together with slight finger pressure.
Bbond os completed in seconds ,or,depending on material in about one minute,leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis -sue paper ,keep out of reach of childrn,in cool dry place.
BOND FOR HOME USES:For mending dishes mad household articles,tables,chairs bureaus and other articles of furniture,fishing tackle and other sports equipment,car fixtures,electrical equipment,or for use on metal leather or paper.
SUPER GLUE GEL 401 ,495 ,406, 416,498 are mades srom cyamoacrylate adhesive,For industrial range ,wood ,rubber,plastics,metal,paper &leather.
APPLICATION:Be sure both surfaces are clean and dry.Apply with extreme care .Never spread with fingers.Apply to only one of the surface,Quickly place two surfaces together with slight finger pressure.
Bbond os completed in seconds ,or,depending on material in about one minute,leave for 24 hours for strongest bond.
Clean away all excess adhesive from container with tis -sue paper ,keep out of reach of childrn,in cool dry place.
BOND FOR HOME USES:For mending dishes mad household articles,tables,chairs bureaus and other articles of furniture,fishing tackle and other sports equipment,car fixtures,electrical equipment,or for use on metal leather or paper.
High Quality Super Glue-12pc on blister card
I.Super glue is single-component cyanoacrylate monomer in liquid state
2.Instant bond in 3seconds
3.With high bonding strength
High Quality Super Glue-12pc on blister card
This instant super glue will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment.
Bond for home uses:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
SPECIFICATIONS:
Bonds in 3-5 Seconds
Validity: 1 year (20
o
C)
Material: Cyanoacrylate Adhesive
Gel content: ≥ 98%
Specific gravity: 1.06±0.02
Gap-fill(mm): 0.25-0.5
Model: fast bonding glue, instant glue, super glue
Shear strength: 7-16 MPa
Active use of phase: 0.05 min
Operating Temperature: around 25
o
C
Shelf life: 12 months
Standard of implementation: SGS MSDS
Warning: Keep out of reach of children:
2.Instant bond in 3seconds
3.With high bonding strength
High Quality Super Glue-12pc on blister card
This instant super glue will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment.
Bond for home uses:
For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper.
SPECIFICATIONS:
Bonds in 3-5 Seconds
Validity: 1 year (20
o
C)
Material: Cyanoacrylate Adhesive
Gel content: ≥ 98%
Specific gravity: 1.06±0.02
Gap-fill(mm): 0.25-0.5
Model: fast bonding glue, instant glue, super glue
Shear strength: 7-16 MPa
Active use of phase: 0.05 min
Operating Temperature: around 25
o
C
Shelf life: 12 months
Standard of implementation: SGS MSDS
Warning: Keep out of reach of children:
High Quality Super Glue
High Quality Super Glue
1, 2000M2 showroom ,30,000 items displaying
2, Strict quality control
3, Low price
High Quality Super Glue
ITEM NO:34015
DESC:cockroach glue trap
PACK:144 pcs/ctn
MEAS:0.028
Packing: 3 PC,6 PC, 8PC, or as ur request.
We offer more than 30000 best selling dollar items to dollar store owners, importers, supermarkets and chain stores around the world. The range of our products from hardware, household product, kitchenware,stationerie to sports goods, Home appliance, can meet all of ur needs. If you are interested to find a perfrect partner and benefit from dollar items or related general marchandise in China,please don't hesitate to contact us at any time.
We are committed to offer good quality product at low price,great packing,samll quantities per item.we also provide one-stop solution of sourcing ,warehouse&logistic for dollar store,discount store items and general merchandise in China.
1, 2000M2 showroom ,30,000 items displaying
2, Strict quality control
3, Low price
High Quality Super Glue
ITEM NO:34015
DESC:cockroach glue trap
PACK:144 pcs/ctn
MEAS:0.028
Packing: 3 PC,6 PC, 8PC, or as ur request.
We offer more than 30000 best selling dollar items to dollar store owners, importers, supermarkets and chain stores around the world. The range of our products from hardware, household product, kitchenware,stationerie to sports goods, Home appliance, can meet all of ur needs. If you are interested to find a perfrect partner and benefit from dollar items or related general marchandise in China,please don't hesitate to contact us at any time.
We are committed to offer good quality product at low price,great packing,samll quantities per item.we also provide one-stop solution of sourcing ,warehouse&logistic for dollar store,discount store items and general merchandise in China.
2011 the newest style of high-temp RTV gasket maker
gasket maker-6739 all1
1. Fast curing and high quality
2. available in many colors
3.resists auto and shop
RTV gasket maker-6739-all1
FEATURE
1
.
Defor RTV SEC-6739 silicone gasket maker is a nuetral cure, sensor-safe,low-odor, non-corrosive compound
2.RTV SEC-6739 meets the performance specs of OE silicone gaskets and retains high flexibility and oil resisstance.
3. temperature range of-75 0F to 662 oF inteermittent and resists auto and shop fluids and vibration
4. available in 85ml tubes
5.available color: black grey red
6.Suggested application include:valve covers;oil pan; intake manifold end seals; Timing covers;Transmission pans
Application
RTV Silicone Gasket Maker can be used almost anywhere a cut gasket of paper, cork, etc.,
was used or to replace previously applied formed in-place gaskets. It is used as a gasket maker in areas with large gaps, such as valve covers,
transmission pans, cover plates, hose connections, timing case covers, oil pans, oil pumps,
thermostat housings, flanges, cam shaft rear covers, pushrod covers, and etc.
SPECIFICATION
PACKING:85G/TUBE,144/PCS,25*25*26CM
DELIVERY TIME: 20- 25 DAYS
CERTIFICATIONS:
1. Fast curing and high quality
2. available in many colors
3.resists auto and shop
RTV gasket maker-6739-all1
FEATURE
1
.
Defor RTV SEC-6739 silicone gasket maker is a nuetral cure, sensor-safe,low-odor, non-corrosive compound
2.RTV SEC-6739 meets the performance specs of OE silicone gaskets and retains high flexibility and oil resisstance.
3. temperature range of-75 0F to 662 oF inteermittent and resists auto and shop fluids and vibration
4. available in 85ml tubes
5.available color: black grey red
6.Suggested application include:valve covers;oil pan; intake manifold end seals; Timing covers;Transmission pans
Application
RTV Silicone Gasket Maker can be used almost anywhere a cut gasket of paper, cork, etc.,
was used or to replace previously applied formed in-place gaskets. It is used as a gasket maker in areas with large gaps, such as valve covers,
transmission pans, cover plates, hose connections, timing case covers, oil pans, oil pumps,
thermostat housings, flanges, cam shaft rear covers, pushrod covers, and etc.
SPECIFICATION
PACKING:85G/TUBE,144/PCS,25*25*26CM
DELIVERY TIME: 20- 25 DAYS
CERTIFICATIONS:
High Quality UV Resistant Neutral curing Silicone Adhesive
JH-3880 Weather Resistant Silicone Adhesive :
1)Single-component ;
2)Excellant weather-resistance;
3)Durability
1.Characteristics:
JH-3880 Weather Resistant
Silicone Adhesive
belongs to
RTV
-1, expediently application between 4~40°C to alcoxy curing system, expediently application between 5~50°C to oxime curing system.
Neutral curing, non-corrosive to glass, coated glass, concrete, marble, metal (not including oxime curing system) and most kinds of plastic, etc;
Quickly speed of curing, excellent
adhesion
, middle , excellent movement capability;
Excellent resistance to weather, the service life is over 50 years in the condition of general weather;
Excellent resistance to low and high temperature change. Little changes of performance at -40~150°C;
Excellent adhesive to most common building material, Special material will have better adhesive with priming;
Good compatibility with other neutral
silicone adesive
;
Belong to non-dissolvent product, low vulcanization shrinkage and green environmental protection product.
2.Purpose:
For weather sealing in glass curtain wall joints;
For weather sealing in aluminum , enamel curtain wall joints;
For sealing in marble (granite),concrete, tile, metal panel materials ect.;
Many other building & Industrial uses.
3.Typical Technology Data:
Performance
Standard
JC/T 882-2001
Measured Value
Testing method
Alcoxy
Oxime
Slumpability (mm)
≤3
0
0
GB/T 13477
Extrusion (ml/min)
≥80
392
336
Tack-Free Time (min)
≤180
30
30
Hardness (HsA)
/
50
48
GB/T 531
Loss of Heating %
≤10
3.3
403
ASTMC 792
Elasticity recovery %
≥80
94.0
90.0
GB/T 13477
Tensile strength in adhesion (Mpa)
≥0.4
0.91
0.83
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Movement Capability %
±20
±20
±20
ASTMC 719
Elongation at ultimate strength %
/
250
260
GB/T 13477
Stability
Store for 12 months at 20~30°C in cool, dry place after date of manufacture.
4.Application Standard:
Standard JC/T 882-2001 Curtain wall sealing
silicone sealant
5.Restriction of Usage
Cant be used as structural
adhesive
;
Unsuitable for the surface of all kinds of material that can effuse grease, plasticizer or solvent;
Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
Unsuitable for the frosty or moist surface;
Unsuitable for the continually soggy or moist place
Cannot be used the product of alcoxy , if the temperature is below 4°C or above 40°C on the surface of the materials; Cannot be used the product of oxime , if the temperature is below 5°C or above 50°C on the surface of the materials.
6.Color and Package:
Color: Black, Gray, White or other colors on request to JH-388
Package: JH-388: 310ml Cartridge net 300ml,
7. Joint Design and Working Procedure:
Please refer to Section The Technology Instruction of Jianhua
Silicone sealant
8. Technical Service
Offer the integral technical data of the
adhesive
9. Maintenance:
We passed the ISO9001 international quality system certification. And we control the quality according to the ISO9001 System strictly.
Insurance agent: PICC
Project photos
1)Single-component ;
2)Excellant weather-resistance;
3)Durability
1.Characteristics:
JH-3880 Weather Resistant
Silicone Adhesive
belongs to
RTV
-1, expediently application between 4~40°C to alcoxy curing system, expediently application between 5~50°C to oxime curing system.
Neutral curing, non-corrosive to glass, coated glass, concrete, marble, metal (not including oxime curing system) and most kinds of plastic, etc;
Quickly speed of curing, excellent
adhesion
, middle , excellent movement capability;
Excellent resistance to weather, the service life is over 50 years in the condition of general weather;
Excellent resistance to low and high temperature change. Little changes of performance at -40~150°C;
Excellent adhesive to most common building material, Special material will have better adhesive with priming;
Good compatibility with other neutral
silicone adesive
;
Belong to non-dissolvent product, low vulcanization shrinkage and green environmental protection product.
2.Purpose:
For weather sealing in glass curtain wall joints;
For weather sealing in aluminum , enamel curtain wall joints;
For sealing in marble (granite),concrete, tile, metal panel materials ect.;
Many other building & Industrial uses.
3.Typical Technology Data:
Performance
Standard
JC/T 882-2001
Measured Value
Testing method
Alcoxy
Oxime
Slumpability (mm)
≤3
0
0
GB/T 13477
Extrusion (ml/min)
≥80
392
336
Tack-Free Time (min)
≤180
30
30
Hardness (HsA)
/
50
48
GB/T 531
Loss of Heating %
≤10
3.3
403
ASTMC 792
Elasticity recovery %
≥80
94.0
90.0
GB/T 13477
Tensile strength in adhesion (Mpa)
≥0.4
0.91
0.83
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Movement Capability %
±20
±20
±20
ASTMC 719
Elongation at ultimate strength %
/
250
260
GB/T 13477
Stability
Store for 12 months at 20~30°C in cool, dry place after date of manufacture.
4.Application Standard:
Standard JC/T 882-2001 Curtain wall sealing
silicone sealant
5.Restriction of Usage
Cant be used as structural
adhesive
;
Unsuitable for the surface of all kinds of material that can effuse grease, plasticizer or solvent;
Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
Unsuitable for the frosty or moist surface;
Unsuitable for the continually soggy or moist place
Cannot be used the product of alcoxy , if the temperature is below 4°C or above 40°C on the surface of the materials; Cannot be used the product of oxime , if the temperature is below 5°C or above 50°C on the surface of the materials.
6.Color and Package:
Color: Black, Gray, White or other colors on request to JH-388
Package: JH-388: 310ml Cartridge net 300ml,
7. Joint Design and Working Procedure:
Please refer to Section The Technology Instruction of Jianhua
Silicone sealant
8. Technical Service
Offer the integral technical data of the
adhesive
9. Maintenance:
We passed the ISO9001 international quality system certification. And we control the quality according to the ISO9001 System strictly.
Insurance agent: PICC
Project photos
High Strength Acrylic Liquid AB Adhesive
High solids and strength,
fast cure time,heat resisitance,
chemical resistance,water resistance,
humidity resistance
1,High solids and strength,
2.fast cure time,heat resisitance,
3.chemical resistance,water resistance,
4.humidity resistance
fast cure time,heat resisitance,
chemical resistance,water resistance,
humidity resistance
1,High solids and strength,
2.fast cure time,heat resisitance,
3.chemical resistance,water resistance,
4.humidity resistance
High Temperature Fine Particle Coating
Two component.Special epoxy system.
Designed for high temperature condition, max. resistant temp. can reach to 235 centigrades.
Introduction
Darbond 1301 is two component, room temperature curing epoxy composite material. It is composed of wear resistant ceramic microspheres and super-hard silicon steel alloy etc. This product has the following advantages:
(1)Good operating property, applicable to vertical surfaces, coating thickness can reach 6mm and above;
(2)Good high temperature resistant property. Max. working temperature range can reach to 235°C at dry working condition;
(3)For max. temperature resistant and protective properties, post cure is necessary;
(4)Cured coating has strong adhesion and excellent properties of wear and impact resistance.
Typical Properties
- Two component.
- Designed to use in high temperature condition, maximum resistant temperature can reach to
235°C.
- Designed to rebuild and protect normal abrasive worn and eroded equipments.
- Designed for rebuilding and
pre-protecting equipments
suffered by high loading fine particle abrasion or erosion in high temperature condition.
Typical Applications
Used for large area repairing and pre-protecting of equipments suffered by load abrasion and erosion wear, such as mortar pump, water pump, induced draft fan impeller and shell, pipeline, elbow, downspouting, slurry pump, hydrocyclone, centrifuge impeller and shell etc.. Suitable for washing and separating system of coal washing and mineral processing; material collecting and conveying system in power plant, cement plant and port etc..
Designed for high temperature condition, max. resistant temp. can reach to 235 centigrades.
Introduction
Darbond 1301 is two component, room temperature curing epoxy composite material. It is composed of wear resistant ceramic microspheres and super-hard silicon steel alloy etc. This product has the following advantages:
(1)Good operating property, applicable to vertical surfaces, coating thickness can reach 6mm and above;
(2)Good high temperature resistant property. Max. working temperature range can reach to 235°C at dry working condition;
(3)For max. temperature resistant and protective properties, post cure is necessary;
(4)Cured coating has strong adhesion and excellent properties of wear and impact resistance.
Typical Properties
- Two component.
- Designed to use in high temperature condition, maximum resistant temperature can reach to
235°C.
- Designed to rebuild and protect normal abrasive worn and eroded equipments.
- Designed for rebuilding and
pre-protecting equipments
suffered by high loading fine particle abrasion or erosion in high temperature condition.
Typical Applications
Used for large area repairing and pre-protecting of equipments suffered by load abrasion and erosion wear, such as mortar pump, water pump, induced draft fan impeller and shell, pipeline, elbow, downspouting, slurry pump, hydrocyclone, centrifuge impeller and shell etc.. Suitable for washing and separating system of coal washing and mineral processing; material collecting and conveying system in power plant, cement plant and port etc..
Friday, September 2, 2011
High Temperature Structural Adhesive/Epoxy 3421
Two component.
Good impact and peeling resistance.
High temperature resistance.
Introduction
Darbond 3421 is two component, room temperature curing epoxy adhesive. It’s made of temperature resistant modified epoxy resin which is specially reinforced and impact resistant. It has excellent properties of impact resistance, peeling resistance, mechanical, electric insulation properties and temperature resistance after cured. It is high temperature resistant and can work at 180°C continuously, intermittent temperature can reach 220°C.
Typical Properties
--Two component.
--Good impact and peeling resistance.
--High temperature resistance, long term working at 180°C, withstands 220°C intermittently.
--Used for bonding metal, ceramic etc. materials, such as NdFeB magnet.
Typical Applications
Applied to high tempearture conditions under 180°C and where high impact strength, peeling strength resistance are required. Suitable for bonding oneself and mutual of metal and ceramic etc, such as bonding of high overload motor NdFeB; bonding of temperature-, wear resistant ceramic tile in power plant, steel plant and cement plant.
Good impact and peeling resistance.
High temperature resistance.
Introduction
Darbond 3421 is two component, room temperature curing epoxy adhesive. It’s made of temperature resistant modified epoxy resin which is specially reinforced and impact resistant. It has excellent properties of impact resistance, peeling resistance, mechanical, electric insulation properties and temperature resistance after cured. It is high temperature resistant and can work at 180°C continuously, intermittent temperature can reach 220°C.
Typical Properties
--Two component.
--Good impact and peeling resistance.
--High temperature resistance, long term working at 180°C, withstands 220°C intermittently.
--Used for bonding metal, ceramic etc. materials, such as NdFeB magnet.
Typical Applications
Applied to high tempearture conditions under 180°C and where high impact strength, peeling strength resistance are required. Suitable for bonding oneself and mutual of metal and ceramic etc, such as bonding of high overload motor NdFeB; bonding of temperature-, wear resistant ceramic tile in power plant, steel plant and cement plant.
High Temperature Vulcanized
High temperature resistance, hydrophobic, nonpoisonous and tasteless
Usage: Mainly uses in aviation, measuring appliance, electric appliance, navigation, metallurgy, machinery, automobile, health, also make each kind of shape of the seal packing collar, the filling piece, the tube, the electric cable
Specification: 1012 1013
Appearance: white or light yellow red
Density(g/m3): 1.05~1.30 1.05~1.30
Hardness(shoreA): 30~70 30~70
Tensile strength(MPa): ≥7.0 ≥7.0
Maximum elongation(%): 200~600 200~600
Tearing strength(kn/m): ≥15 ≥15
Heat resistant range(°C): 280 300
Packing: Paper box inside lining plastic film, 20kg/box
Storage:Self life 1 year
Update Date:2011-8-10 1:50:07
Usage: Mainly uses in aviation, measuring appliance, electric appliance, navigation, metallurgy, machinery, automobile, health, also make each kind of shape of the seal packing collar, the filling piece, the tube, the electric cable
Specification: 1012 1013
Appearance: white or light yellow red
Density(g/m3): 1.05~1.30 1.05~1.30
Hardness(shoreA): 30~70 30~70
Tensile strength(MPa): ≥7.0 ≥7.0
Maximum elongation(%): 200~600 200~600
Tearing strength(kn/m): ≥15 ≥15
Heat resistant range(°C): 280 300
Packing: Paper box inside lining plastic film, 20kg/box
Storage:Self life 1 year
Update Date:2011-8-10 1:50:07
High conductivity silicone thermal grease with RoSH test report
silicone thermal grease
1 Excellent thermal conductivity
2 Excellent electrical insulation
3 Wide operating temper
High conductivity silicone thermal grease with RoSH test report
Description
Excellent thermal conductivity depends on the heat transfer media between devices and a good interface. Silicone has low surface tension to wet most of the surface to reduce thermal contact resistance between the substrate and material resistance. SC1001 Thermal Grease belongs to a type of one-component silicon-based material. It is non-toxic, tasteless, non-corrosive, Wetting, without precipitation.
Main Features
1. Excellent thermal conductivity (heat dissipation).
2. Excellent electrical insulation, using stability, and construction performance.
3. Wide operating temperature.
Usage
Clean surface:
Clean surface, remove rust, dust and oil and so on.
Coated with silicone grease: Apply thermal grease evenly on the surface of the device.
Typical Usage
It can be widely used in the heat transfer medium of electronic components, such as the CPU chip, power blocks, transistor, thyristor and diode and the substrate (aluminum, copper).
performance data
Unit
APS SC1001
Appearance
White cream
corrosion
No corrosion
Penetration
1/10mm
200-300
Proportion
2.2
Temperature range
°C
-60-+280
Oil scatteration
% / 200°C8HR
≤1.8
Volatility
% / 200°C8HR
≤1.9
Thermal conductivity
[W/(m*K)]
1.2
Store
1. In a dry and cool place, avoid direct sunlight.
2. Out of the reach of children.
3. Clean the surface to get the best thermal performance.
4. In case of contact with eyes, please clean with water, and go to hospital.
5. Avoid prolonged contact with skin.
6. General storage period is two years.
Package
45mL/tube, 100mL/tube, 1kg/can.
1 Excellent thermal conductivity
2 Excellent electrical insulation
3 Wide operating temper
High conductivity silicone thermal grease with RoSH test report
Description
Excellent thermal conductivity depends on the heat transfer media between devices and a good interface. Silicone has low surface tension to wet most of the surface to reduce thermal contact resistance between the substrate and material resistance. SC1001 Thermal Grease belongs to a type of one-component silicon-based material. It is non-toxic, tasteless, non-corrosive, Wetting, without precipitation.
Main Features
1. Excellent thermal conductivity (heat dissipation).
2. Excellent electrical insulation, using stability, and construction performance.
3. Wide operating temperature.
Usage
Clean surface:
Clean surface, remove rust, dust and oil and so on.
Coated with silicone grease: Apply thermal grease evenly on the surface of the device.
Typical Usage
It can be widely used in the heat transfer medium of electronic components, such as the CPU chip, power blocks, transistor, thyristor and diode and the substrate (aluminum, copper).
performance data
Unit
APS SC1001
Appearance
White cream
corrosion
No corrosion
Penetration
1/10mm
200-300
Proportion
2.2
Temperature range
°C
-60-+280
Oil scatteration
% / 200°C8HR
≤1.8
Volatility
% / 200°C8HR
≤1.9
Thermal conductivity
[W/(m*K)]
1.2
Store
1. In a dry and cool place, avoid direct sunlight.
2. Out of the reach of children.
3. Clean the surface to get the best thermal performance.
4. In case of contact with eyes, please clean with water, and go to hospital.
5. Avoid prolonged contact with skin.
6. General storage period is two years.
Package
45mL/tube, 100mL/tube, 1kg/can.
High grade Neutral Silicone weather-resistant sealant
1,neutral curing silicone sealant,
2,non-corrosive to many materia,
3,excellent adhesion and movement capability,
FENGBA-N88 is one component room temperature neutral curing silicone sealant, non-corrosive to glass, coated glass, concrete, marble, and most kinds of plastic, etc;
It has good adhesion and movement capability, excellent
ageing-resistant performance and excellent adhesive to most common building material. Which has little changes of performance at -40~150°C.
APPLICATION
It is mainly used in enamel, curtain wall, porcelain,stainless steels and many other building & Industrial uses.
Bonding and sealing for non-structure assembling of glass, aluminum plastic plate, concrete, aluminum product, tile, ceramic products and other building material, as well as other purpose. They are mainly used for caulking sealing during erection of various doors and windows.
2,non-corrosive to many materia,
3,excellent adhesion and movement capability,
FENGBA-N88 is one component room temperature neutral curing silicone sealant, non-corrosive to glass, coated glass, concrete, marble, and most kinds of plastic, etc;
It has good adhesion and movement capability, excellent
ageing-resistant performance and excellent adhesive to most common building material. Which has little changes of performance at -40~150°C.
APPLICATION
It is mainly used in enamel, curtain wall, porcelain,stainless steels and many other building & Industrial uses.
Bonding and sealing for non-structure assembling of glass, aluminum plastic plate, concrete, aluminum product, tile, ceramic products and other building material, as well as other purpose. They are mainly used for caulking sealing during erection of various doors and windows.
High grade acetoxy silicone sealant
1, RTV acetoxy silicone sealant
2, Gengeral Purpose
3, Excellent adhesion
4, Application Standard: GB/T 14683-2003
1
,
Characteristics:
One component RTV acetoxy silicone sealant;
Excellent weatherproofing performance;
Good adhesion to various building materials.
2
,
Main Purpose:
Assembly for various glass windows and doors;
Joint and seal for interior decorative glass;
General joint and seal.
3
,
Main Technology Data:
Performance
Standard
Measured Value
Testing Method
Slump
Horizontal
Undeformed
undeformed
GB/T 13477
Vertical(mm)
≤3
0
GB/T 13477
Extrusion ml/min
≥80
320
GB/T 13477
Skin Time min
≤180
10
GB/T 13477
Hardness(HsA)
20-60
25
GB/T 531
Tensile Modulus Mpa
≤0.4
0.3
GB/T 13477
Tensile proper
No damage
No damage
GB/T 13477
Storage
9 months shelf life if stored below 27 degrees centigrade in cool, dry places after the date of production
4,Application Standard: GB/T 14683-2003
5,
Restriction of Usage:
Cannot be used as structural sealant;
Not compatible with the materials of grease or exudation;
Unsuitable for airproof location, for it requires absorbing moisture in air to cure;
Unsuitable for frosty or moist surface;
Unsuitable for continually flooding or entire-year moist place;
Corrosive to the materials of concrete, porosint stone, zinc and iron;
Cannot be used when the substrate temperature is under 6°C or above 40°C.
6. Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
7,
Construction Method:
Please do adhesion test or compatibility test to assure the applicability of product;
Please clean the joint with solvent such as toluene, xylene and acetone, then keep it dry;
Tape is used to cover the deges of the joint to make silicone sealant sealed perfectly, but it cannot contact the sealed surface;
Cut the nozzle at the desired size. Keep good contact between the silicone sealant and joint, and remove the tape before the sealant is cured;
Please keep ventilate for the construction site.
8. Safety
l Silicone sealant will release volatile compound so that it could be harmful to health, therefore, please keep good and ventilate;Silicone sealant will not release any harmful substance and not be harmful to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
9. Warranty
l As an ISO9001,ISO14001 certified company, we are committed to establish and implement the ISO9001 Quality Management System.
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
2, Gengeral Purpose
3, Excellent adhesion
4, Application Standard: GB/T 14683-2003
1
,
Characteristics:
One component RTV acetoxy silicone sealant;
Excellent weatherproofing performance;
Good adhesion to various building materials.
2
,
Main Purpose:
Assembly for various glass windows and doors;
Joint and seal for interior decorative glass;
General joint and seal.
3
,
Main Technology Data:
Performance
Standard
Measured Value
Testing Method
Slump
Horizontal
Undeformed
undeformed
GB/T 13477
Vertical(mm)
≤3
0
GB/T 13477
Extrusion ml/min
≥80
320
GB/T 13477
Skin Time min
≤180
10
GB/T 13477
Hardness(HsA)
20-60
25
GB/T 531
Tensile Modulus Mpa
≤0.4
0.3
GB/T 13477
Tensile proper
No damage
No damage
GB/T 13477
Storage
9 months shelf life if stored below 27 degrees centigrade in cool, dry places after the date of production
4,Application Standard: GB/T 14683-2003
5,
Restriction of Usage:
Cannot be used as structural sealant;
Not compatible with the materials of grease or exudation;
Unsuitable for airproof location, for it requires absorbing moisture in air to cure;
Unsuitable for frosty or moist surface;
Unsuitable for continually flooding or entire-year moist place;
Corrosive to the materials of concrete, porosint stone, zinc and iron;
Cannot be used when the substrate temperature is under 6°C or above 40°C.
6. Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
7,
Construction Method:
Please do adhesion test or compatibility test to assure the applicability of product;
Please clean the joint with solvent such as toluene, xylene and acetone, then keep it dry;
Tape is used to cover the deges of the joint to make silicone sealant sealed perfectly, but it cannot contact the sealed surface;
Cut the nozzle at the desired size. Keep good contact between the silicone sealant and joint, and remove the tape before the sealant is cured;
Please keep ventilate for the construction site.
8. Safety
l Silicone sealant will release volatile compound so that it could be harmful to health, therefore, please keep good and ventilate;Silicone sealant will not release any harmful substance and not be harmful to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
9. Warranty
l As an ISO9001,ISO14001 certified company, we are committed to establish and implement the ISO9001 Quality Management System.
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
High performance PU Foam
High performance PU Foam is very good for filling and sealing with with excellent mounting capacities,
Baiyun High performance PU Foam is a one-component,ready to use multi-purpose polyurethane foam.It is fitted with a plastic adaptor head for use with a foam application gun or a straw.The foam will expand and cure by moisture in the air.It is used for a wide range of building applications.It is very good for filling and sealing with with excellent mounting capacities, high thermal and acoustical insulation.
Base
Polyurethane
Consistency
Stable Foam
Curing System
Moisture-cure
Tack-Free Time (min)
7~15
Drying Time
Dust-free after 20-25 min.
Cutting Time (hour)
1~2 (+25°C)
3~4 (-5°C)
Yield (L)
40~45
Shrink
None
Post Expansion
None
Cellular Structure
50~60% open cells
Specific Gravity (kg/m³)
20~25
Temperature Resistance
-40°C~+80°C
Application Temperature Range
-10°C~+40°C
Colour
Champagne
Fire Class (DIN 4102 )
B3
Insulation Factor (Mw/m.k)
<30
Compressive Strength (kPa)
>150
Tensile Strength (kPa)
>30 (10%)
Adhesive Strengh(kPa)
>100
Water Absorption (ML)
0.3~1(no epidermis)
<0.1(with epidermis)
Product Temperature Features
l Good adhesion to a wide variety of surfaces such as UPVC masonry,brick,block work,glass,steel ,aluminum, timber and other substrates (except PP,PE and Teflon).
l Better adhesion than normal quality PU foam.Stronger after cured.No shrinkage after cured.
l Application temperature is -10°C to +40 °C.
l Optimal application temperature is between +10°C to +30°C.
l It contains CFC-free propellants which are harmless to the ozene layer.
Applications
l Installing ,fixing and insulating of door and window frames
l Filling and sealing of gaps,joint,openings and cavities
l Connecting of insulation materials and roof construction
l Bonding and mounting
l Insulating the electrical outlets and water pipes
l Heat preservation, cold and sound insulation
l Packaging purpose, wrap the precious & fragile commodity shake-proof and anti-pressure
Shelf Life
12 months store in shade,cool and well ventilated place under 25°C.
Packing
12 pcs/can
Safety
Contains Diphenylmethane-4,4-diiscoyanate,harmful by inhalation, irritating to eyes, respiratory system and skin, in case of eye contact, flush with water and get immediate medical attention; Do not breathe spray/vapor; Use in well-ventilated areas; Wear suitable protective clothing, gloves and goggles; Pressurized container; Keep away from direct sunlight and do not expose temperatures over 50°C ; Do not burn or pierce, even after use; Keep away from heat,sparks,flames and static electricity; Turn off sources of ignition(pilot light etc.);Keep out of the reach of children.
Baiyun High performance PU Foam is a one-component,ready to use multi-purpose polyurethane foam.It is fitted with a plastic adaptor head for use with a foam application gun or a straw.The foam will expand and cure by moisture in the air.It is used for a wide range of building applications.It is very good for filling and sealing with with excellent mounting capacities, high thermal and acoustical insulation.
Base
Polyurethane
Consistency
Stable Foam
Curing System
Moisture-cure
Tack-Free Time (min)
7~15
Drying Time
Dust-free after 20-25 min.
Cutting Time (hour)
1~2 (+25°C)
3~4 (-5°C)
Yield (L)
40~45
Shrink
None
Post Expansion
None
Cellular Structure
50~60% open cells
Specific Gravity (kg/m³)
20~25
Temperature Resistance
-40°C~+80°C
Application Temperature Range
-10°C~+40°C
Colour
Champagne
Fire Class (DIN 4102 )
B3
Insulation Factor (Mw/m.k)
<30
Compressive Strength (kPa)
>150
Tensile Strength (kPa)
>30 (10%)
Adhesive Strengh(kPa)
>100
Water Absorption (ML)
0.3~1(no epidermis)
<0.1(with epidermis)
Product Temperature Features
l Good adhesion to a wide variety of surfaces such as UPVC masonry,brick,block work,glass,steel ,aluminum, timber and other substrates (except PP,PE and Teflon).
l Better adhesion than normal quality PU foam.Stronger after cured.No shrinkage after cured.
l Application temperature is -10°C to +40 °C.
l Optimal application temperature is between +10°C to +30°C.
l It contains CFC-free propellants which are harmless to the ozene layer.
Applications
l Installing ,fixing and insulating of door and window frames
l Filling and sealing of gaps,joint,openings and cavities
l Connecting of insulation materials and roof construction
l Bonding and mounting
l Insulating the electrical outlets and water pipes
l Heat preservation, cold and sound insulation
l Packaging purpose, wrap the precious & fragile commodity shake-proof and anti-pressure
Shelf Life
12 months store in shade,cool and well ventilated place under 25°C.
Packing
12 pcs/can
Safety
Contains Diphenylmethane-4,4-diiscoyanate,harmful by inhalation, irritating to eyes, respiratory system and skin, in case of eye contact, flush with water and get immediate medical attention; Do not breathe spray/vapor; Use in well-ventilated areas; Wear suitable protective clothing, gloves and goggles; Pressurized container; Keep away from direct sunlight and do not expose temperatures over 50°C ; Do not burn or pierce, even after use; Keep away from heat,sparks,flames and static electricity; Turn off sources of ignition(pilot light etc.);Keep out of the reach of children.
High performance super glue
1)high performance super glue
2)top quality
3)competitive price and prompt delivery
4)professional service
High performance super glue is cyanocrylate adhesive with features of instant bonding. The single component adhesive that bond almost all close-fitting smooth surface in seconds. It requires no mixing, no heating, no clamping. These adhesive contain no solvent, have low toxicity, mild odor and non-flammable.
Item Name
HIGH PERFORMANCE SUPER GLUE
Item NO.
AY
Application
For repair iron, ceramics, equipment
Specification
15G; 20G and so on
Package
24bottles/carton 144bottles/carton and so on
Measurement
It's up to package
OEM
Available
Appearance
Liquid, clear
Shelf life
12 months
Certification
MSDS; CE; SGS
Package details:
Art.No
Description
Spec.
Card/ CTN
Shelf life
CTN Size(cm)
FCL 20'
High performance CA
20g/ plastic bottle
20g
12
24 months
11x11x14
16250
Rubber toughness CA
20g/ plastic bottle
20g
250
24 months
42X21.5X55
560
OEM serve is warmly welcomed!!
2)top quality
3)competitive price and prompt delivery
4)professional service
High performance super glue is cyanocrylate adhesive with features of instant bonding. The single component adhesive that bond almost all close-fitting smooth surface in seconds. It requires no mixing, no heating, no clamping. These adhesive contain no solvent, have low toxicity, mild odor and non-flammable.
Item Name
HIGH PERFORMANCE SUPER GLUE
Item NO.
AY
Application
For repair iron, ceramics, equipment
Specification
15G; 20G and so on
Package
24bottles/carton 144bottles/carton and so on
Measurement
It's up to package
OEM
Available
Appearance
Liquid, clear
Shelf life
12 months
Certification
MSDS; CE; SGS
Package details:
Art.No
Description
Spec.
Card/ CTN
Shelf life
CTN Size(cm)
FCL 20'
High performance CA
20g/ plastic bottle
20g
12
24 months
11x11x14
16250
Rubber toughness CA
20g/ plastic bottle
20g
250
24 months
42X21.5X55
560
OEM serve is warmly welcomed!!
201A UF Resin Powder
201A UF Resin Powder
Usage:Woodworking Adhesive
Productivity:1200MT/month
Certificate:ISO9001-2008
1. Product Specialty:
1. High Bonding Strength
2. One component UF Resin Powder, Convenient for Use
3. Formaldehyde Emission reach to International Standard
4. Ideal effect for Cold, Heat solidification
5. Similar to wood color, no pollution on wood
6. Excellent Water-proofing performance
7. Convenient for transportation
2. Application Areas:
1. Various kind of artificial boards
2. Gluing Plywood & Bentwood
3. Surface veneer of door and decorative boards
4. Engineered solid wood flooring
5. Wooden furniture, doors and windows etc.
3. Performance Index
Item Unit Description
Appearance White Powder
Moisture Content % ≤1
Curing Time (20) h 8
Shearing StrengthUnder Pressure after 20h MPa >15
Shearing Strength of Water ResistanceUnder Water after 24h MPa >11
Active Period after Mixture 40 / 20 Hour 4/8
4. Usage Method:
1. Pretreatment for gluing wood material:
a) Moisture content reach to 10 + 2%
b) Remove Knots, Cracks, oil stain and resin etc.
c) Wood surface must be flat and smooth. (Thickness Tolerance0.1mm
2. Mixture of Glue
a) Mixture Ratio(weight): UF Powder: Water=1: ≤0.6
b) Dissolution Method:
Put 2/3 of the total needed water into mixer, and then add UF powder in.
Switch on the mixer with speed of 50~150 rotations / minute, after glue
powder being completely dissolved in water, put the remained 1/3 water in
mixer and stir for 3~5minutes till glue to being completely dissolved.
c) Workable period of dissolved liquid glue is 4~8 hours under room
temperature.
3. Gluing Operation:
a) Gluing Quantity: Depend on different wood material and working
temperature. Generally, 2 sides sub is: 200~300g/m2.
b) Required Press Condition: (Solidification under room temperature)
The pressure and Process Time depend on different wood species and
process temperature. Please refer to below instruction:
Wood Species Coniferous wood Broad-leaved wood
Temperature 5-25 >25 5-25 >25
Gluing Qty(2 sides) (g/m²) 200-250 250-300 200-250 250-300
Pressure (MPa) 0.8-1.0 0.8-1.0 1.2-1.5 1.2-1.5
Press Time (hour) >8 >7 >8 >8
c) Maintenance:
After pressure relief, the glued board could be processed on second
day. In winter, board must be maintained at least 12 hours under
temperature above 20 before put into process.
4. Heating Solidification Operation:
The glued board with above mentioned pressure for 5~7minutes under
temperature 100~110, could be used after release of press.
5. Storage and Note:
1) Storage life: 1 years under temperature lower than 30.
2) The goods should be stored in a dry, ventilated location. Avoid direct sunshine
and moisture.
3) The package should be sealed again immediately once the pack has been
opened to avoid moisture.
4) Avoid contact with eyes. Once splashed into eyes, flushed out with plenty of
clean water. Consults doctor if necessary.
6. Package:
1. 3-ply paper bag with polyethylene liners.
2. 20kg/package.
Usage:Woodworking Adhesive
Productivity:1200MT/month
Certificate:ISO9001-2008
1. Product Specialty:
1. High Bonding Strength
2. One component UF Resin Powder, Convenient for Use
3. Formaldehyde Emission reach to International Standard
4. Ideal effect for Cold, Heat solidification
5. Similar to wood color, no pollution on wood
6. Excellent Water-proofing performance
7. Convenient for transportation
2. Application Areas:
1. Various kind of artificial boards
2. Gluing Plywood & Bentwood
3. Surface veneer of door and decorative boards
4. Engineered solid wood flooring
5. Wooden furniture, doors and windows etc.
3. Performance Index
Item Unit Description
Appearance White Powder
Moisture Content % ≤1
Curing Time (20) h 8
Shearing StrengthUnder Pressure after 20h MPa >15
Shearing Strength of Water ResistanceUnder Water after 24h MPa >11
Active Period after Mixture 40 / 20 Hour 4/8
4. Usage Method:
1. Pretreatment for gluing wood material:
a) Moisture content reach to 10 + 2%
b) Remove Knots, Cracks, oil stain and resin etc.
c) Wood surface must be flat and smooth. (Thickness Tolerance0.1mm
2. Mixture of Glue
a) Mixture Ratio(weight): UF Powder: Water=1: ≤0.6
b) Dissolution Method:
Put 2/3 of the total needed water into mixer, and then add UF powder in.
Switch on the mixer with speed of 50~150 rotations / minute, after glue
powder being completely dissolved in water, put the remained 1/3 water in
mixer and stir for 3~5minutes till glue to being completely dissolved.
c) Workable period of dissolved liquid glue is 4~8 hours under room
temperature.
3. Gluing Operation:
a) Gluing Quantity: Depend on different wood material and working
temperature. Generally, 2 sides sub is: 200~300g/m2.
b) Required Press Condition: (Solidification under room temperature)
The pressure and Process Time depend on different wood species and
process temperature. Please refer to below instruction:
Wood Species Coniferous wood Broad-leaved wood
Temperature 5-25 >25 5-25 >25
Gluing Qty(2 sides) (g/m²) 200-250 250-300 200-250 250-300
Pressure (MPa) 0.8-1.0 0.8-1.0 1.2-1.5 1.2-1.5
Press Time (hour) >8 >7 >8 >8
c) Maintenance:
After pressure relief, the glued board could be processed on second
day. In winter, board must be maintained at least 12 hours under
temperature above 20 before put into process.
4. Heating Solidification Operation:
The glued board with above mentioned pressure for 5~7minutes under
temperature 100~110, could be used after release of press.
5. Storage and Note:
1) Storage life: 1 years under temperature lower than 30.
2) The goods should be stored in a dry, ventilated location. Avoid direct sunshine
and moisture.
3) The package should be sealed again immediately once the pack has been
opened to avoid moisture.
4) Avoid contact with eyes. Once splashed into eyes, flushed out with plenty of
clean water. Consults doctor if necessary.
6. Package:
1. 3-ply paper bag with polyethylene liners.
2. 20kg/package.
High quality Gum Rosin WW Grade (CAS NO.8050-09-7)
Gum Rosin
Grade:X, WW, WG, N, M,K
Packing: 225kgs drum, 21.6mt/20"FCL
Made in China
Used in paper, ink, rubber, paints ETC.
Gum Rosin ww grade, resin
Used in paper, ink, rubber, paints and varnish, various adhesives, glue, soap, synthetic resins.
Features:
1) China original gum rosin WW grade
2) Natural organic compound, mainly composed of resins
3) Possesses chemical activity when dissolved in many organic solvents
4) Used for the manufacturing of paper, paint, soap and printing ink
5) Easily softened and oxidized
6) In the oil paint industry, the carboxylation reaction of resin acid is usually employed to produce resinate for further use
7) In the producing of synthetic rubber and printing ink, resin acid is changed into disproportionate rosin, polymerized rosin, hydrogenated rosin, for further use by its double bond reaction
Packing:In galvanized iron drumAbout 225kg/drum
Conveyance:Qty/20' FCL: 21.6MT
It is used in paper, ink, rubber, paints and varnish, various adhesives, glue, soap, synthetic resins, chewing gum and other chemical industries
Grade:X, WW, WG, N, M,K
Packing: 225kgs drum, 21.6mt/20"FCL
Made in China
Used in paper, ink, rubber, paints ETC.
Gum Rosin ww grade, resin
Used in paper, ink, rubber, paints and varnish, various adhesives, glue, soap, synthetic resins.
Features:
1) China original gum rosin WW grade
2) Natural organic compound, mainly composed of resins
3) Possesses chemical activity when dissolved in many organic solvents
4) Used for the manufacturing of paper, paint, soap and printing ink
5) Easily softened and oxidized
6) In the oil paint industry, the carboxylation reaction of resin acid is usually employed to produce resinate for further use
7) In the producing of synthetic rubber and printing ink, resin acid is changed into disproportionate rosin, polymerized rosin, hydrogenated rosin, for further use by its double bond reaction
Packing:In galvanized iron drumAbout 225kg/drum
Conveyance:Qty/20' FCL: 21.6MT
It is used in paper, ink, rubber, paints and varnish, various adhesives, glue, soap, synthetic resins, chewing gum and other chemical industries
High quality acrylic caulk
Acrylic caulk is Suitable for most interior or exterior applications.
KTR700 ULTRA WHITE CAULK
ELASTOMERIC ACRYLIC SEALANT
30-Year Warranty
(ASTM C 834-91)
PRODUCT DESCRIPTION:
A one-component, non-staining high-performance with excellent resistance to air and moisture penetration and UV rays that cures into a flexible rubber sand gasket that will not crack, even after many years of outdoor exposure; can be paited over shortly after application with latex or oil paint.
BASIC USES:
Suitable for most interior or exterior applications. Seals cracks on concrete, drywall and wood; excellent for caulking around doors and window frames, siding corner joints, skylights, vents, air ducts and chimneys, where joint movement is moderate.
PRODUCT ADVANTAGES:
*Seals cracks in concrete
*100% paintable in two hours
*100% water cleanup
*Mildew and moisture resistant
*100% flexible
*100% exterior / interior
*100% elastomeric
* Non-yellowing white finish
TECHNICAL DATA
Percent Solids: 70.00±1% by weight
55.59±1% by volume
Colors: Ultra white
Weight / Gallon: 11.65±0.5 lbs
Viscosity: 300,000-350, 000 cps.
Flash Point: Non-flammable
Drying Time: Tack free: 15 minutes
To coat with latex paint: 2 hours
To coat with alkyd paint: 24 hours
Flash Point: Non-flammable
Size: 10.1-oz. cartridge
Theoretical Coverage: Approximately 34 linear feet of 1/4 bead per 10.1-oz. Cartridge.
Surface Preparation:Surface must be free of dust, dirt, grease and mildew. Remove all loose or badly cracked sealant and paint.
Mildewed Surfaces: Any existing mildew on the surface must be completely killed and removed prior to the application of new caulk. Using a long-handled brush, scrub mildewed surface with a mixture of one quart of household bleach and three quarts of warm water. Rinse completely and let dry completely.
Previously Cualked Surfaces: It is critical to remove as much old sealant as possible before applying new caulk, spefially if it is cracked, eroded or pulled away from the joint.
Application Instructions: For best results, follow these steps:
(1) Apply at temperature above 40F (5) and when no precipitation is expected within 72 hours.
(2) Cut nozzle to desired bead size (1/4 is recommended).
(3) Hold tube at 45
o
angle to the seam and push KTR700 ULTRA WHITE CAULK ahead of nozzle, applying uniform to the trigger in order to get a smooth bead.
(4) Tool within 15 minutes with finger or damp smooth sponge.
(5) Limit joint size to be filled to approximately 3/8X3/8. If depth of joint exceeds 3/8, use polyethylene foam or oakum as backup filler.
(6) Wipe away excess with a damp cloth before surface skins.
Drying Time: Wait two hours before painting with latex paint; 24 hours if using alkyd (oil based) paint.
Cleanup: Clean up excess with damp cloth before caulk cures.
Coverage: Approximately 34 linear feet of 1/4 bead per 10.1-oz. Cartridge.
Storage: Protect from freezing; store in a cool, dry place at room temperature. Product must be used within one year of purchase.
Note: Always use a sealer as shellac, before topcoating with a lacquer. Not recommended for use on horizontal surface where water may collect, or for marine use on areas below water level.
Limited Warranty: Satisfaction guaranteed for thirty years. If porduct cracks, peels or separates while you own your home during periold of guarantee when used as directed, returen sales receipt and used container to KATER ADHESIVES INDUSTRIAL CO., LTD. Seller will not accept liability for mre than product replacement or purchase price.
Notice: The technical data contained herin are true and accurate to the best of our knowledge. Published technical data and instructions are subject to change without prior notice.
KTR700 ULTRA WHITE CAULK
ELASTOMERIC ACRYLIC SEALANT
30-Year Warranty
(ASTM C 834-91)
PRODUCT DESCRIPTION:
A one-component, non-staining high-performance with excellent resistance to air and moisture penetration and UV rays that cures into a flexible rubber sand gasket that will not crack, even after many years of outdoor exposure; can be paited over shortly after application with latex or oil paint.
BASIC USES:
Suitable for most interior or exterior applications. Seals cracks on concrete, drywall and wood; excellent for caulking around doors and window frames, siding corner joints, skylights, vents, air ducts and chimneys, where joint movement is moderate.
PRODUCT ADVANTAGES:
*Seals cracks in concrete
*100% paintable in two hours
*100% water cleanup
*Mildew and moisture resistant
*100% flexible
*100% exterior / interior
*100% elastomeric
* Non-yellowing white finish
TECHNICAL DATA
Percent Solids: 70.00±1% by weight
55.59±1% by volume
Colors: Ultra white
Weight / Gallon: 11.65±0.5 lbs
Viscosity: 300,000-350, 000 cps.
Flash Point: Non-flammable
Drying Time: Tack free: 15 minutes
To coat with latex paint: 2 hours
To coat with alkyd paint: 24 hours
Flash Point: Non-flammable
Size: 10.1-oz. cartridge
Theoretical Coverage: Approximately 34 linear feet of 1/4 bead per 10.1-oz. Cartridge.
Surface Preparation:Surface must be free of dust, dirt, grease and mildew. Remove all loose or badly cracked sealant and paint.
Mildewed Surfaces: Any existing mildew on the surface must be completely killed and removed prior to the application of new caulk. Using a long-handled brush, scrub mildewed surface with a mixture of one quart of household bleach and three quarts of warm water. Rinse completely and let dry completely.
Previously Cualked Surfaces: It is critical to remove as much old sealant as possible before applying new caulk, spefially if it is cracked, eroded or pulled away from the joint.
Application Instructions: For best results, follow these steps:
(1) Apply at temperature above 40F (5) and when no precipitation is expected within 72 hours.
(2) Cut nozzle to desired bead size (1/4 is recommended).
(3) Hold tube at 45
o
angle to the seam and push KTR700 ULTRA WHITE CAULK ahead of nozzle, applying uniform to the trigger in order to get a smooth bead.
(4) Tool within 15 minutes with finger or damp smooth sponge.
(5) Limit joint size to be filled to approximately 3/8X3/8. If depth of joint exceeds 3/8, use polyethylene foam or oakum as backup filler.
(6) Wipe away excess with a damp cloth before surface skins.
Drying Time: Wait two hours before painting with latex paint; 24 hours if using alkyd (oil based) paint.
Cleanup: Clean up excess with damp cloth before caulk cures.
Coverage: Approximately 34 linear feet of 1/4 bead per 10.1-oz. Cartridge.
Storage: Protect from freezing; store in a cool, dry place at room temperature. Product must be used within one year of purchase.
Note: Always use a sealer as shellac, before topcoating with a lacquer. Not recommended for use on horizontal surface where water may collect, or for marine use on areas below water level.
Limited Warranty: Satisfaction guaranteed for thirty years. If porduct cracks, peels or separates while you own your home during periold of guarantee when used as directed, returen sales receipt and used container to KATER ADHESIVES INDUSTRIAL CO., LTD. Seller will not accept liability for mre than product replacement or purchase price.
Notice: The technical data contained herin are true and accurate to the best of our knowledge. Published technical data and instructions are subject to change without prior notice.
High quality hot melt adhesive
hot melt adhesive
1. Material:EVA and Resin
2. Size: 11*190mm and as your require
3. Various usage
4.Eco-friendly
Hot Melt Adhesive
1)Name:hot melt adhesive/hot melt adhesive stick
2)Size:various
3)Packing:13kg/carton(N.W.) or others
4)MOQ:500kg
5)Payment term:T/T
Carton Measurement:53*22*16
CBM:0.01865
G.W 13.5KG
N.W 13KG
Good quality with cheap price
We can offer high quality hotmelt glue sticks that are made using high quality adhesive materials.
We guaratee our products to have have highest standards yet maintianing our competetive edge!
1. Material:EVA and Resin
2. Size: 11*190mm and as your require
3. Various usage
4.Eco-friendly
Hot Melt Adhesive
1)Name:hot melt adhesive/hot melt adhesive stick
2)Size:various
3)Packing:13kg/carton(N.W.) or others
4)MOQ:500kg
5)Payment term:T/T
Carton Measurement:53*22*16
CBM:0.01865
G.W 13.5KG
N.W 13KG
Good quality with cheap price
We can offer high quality hotmelt glue sticks that are made using high quality adhesive materials.
We guaratee our products to have have highest standards yet maintianing our competetive edge!
High quality structural silicone sealant
For glass,stone material,aluminium-alloy,dot-type or exposure frame curtain wall's glass,big flat glass,day-lighting ceiling.
HX-8688 High quality structural silicone sealant
Characteristics
l One component, RTV-1, Neutral Curing at room temperature, high strength silicone structural sealant.
l Excellent weatherproofing performance, shelf life reaches over 30 years in general weather condition.
l No need to prime coated, excellent joint to most building material.
l Excellent compatibility with other neutral silicone sealant.
The Main Usage
l Sealing and connecting for glass,aluminium plate,stone material(marble,granite) and aluminium-alloy with each other.
l Structurally glazing in big flat glass and glass roof structural engineering.
l Seal joint for various glass installation engineering.
l Secondary sealing for hollow glass.
Application Standard
l GB 16776-2005
Specification
l 300ml/cartridge; 24cartridge/ctn
l 590ml/sausage; 20sausage/ctn
l Color: Transparent,Aluminum,White,Black,Grey,Silver Grey
Restriction of Usage
l Not compatible with materials with grease or exudation.
l Unsuitable for the airproof location, because it is required to absorb moisture in air to cure.
l Unsuitable for the frosty or moist surface.
l Unsuitable for the continually flooding or entire-year moist places.
l Cannot be used on the unclean or unstable substrate.
l Cannot be used on the substrate surface under 6°C or above 40°C.
l Cannot be used on joint which bearing structural strength or places of physical damage.
Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
Safety
l Silicone sealant will release volatile compound so that it could be harm to health, therefore, please keep good and ventilate;
l Silicone sealant will not release any harmful substance and anything harm to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
Warranty
l As an ISO9001 certified company, we are committed to establish and implement the ISO9001 Quality Management System. We are recognized as manufacturer of silicone structural sealant for construction on August,2010.
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
Maintenance
l Generally there is no need to repair. If the seal joint is damaged, please remove the damaged silicone sealant, clean the surface of substrates, and fill up with silicone sealant.
l Hexin silicone sealants have good adhesion to cured sealant.
Purchase Channel and Price
l Users can buy Hexin silicone sealant from Guangzhou Hexin Industry Co.,Ltd and appointed regional agents to ensure the quality and realness
HX-8688 High quality structural silicone sealant
Characteristics
l One component, RTV-1, Neutral Curing at room temperature, high strength silicone structural sealant.
l Excellent weatherproofing performance, shelf life reaches over 30 years in general weather condition.
l No need to prime coated, excellent joint to most building material.
l Excellent compatibility with other neutral silicone sealant.
The Main Usage
l Sealing and connecting for glass,aluminium plate,stone material(marble,granite) and aluminium-alloy with each other.
l Structurally glazing in big flat glass and glass roof structural engineering.
l Seal joint for various glass installation engineering.
l Secondary sealing for hollow glass.
Application Standard
l GB 16776-2005
Specification
l 300ml/cartridge; 24cartridge/ctn
l 590ml/sausage; 20sausage/ctn
l Color: Transparent,Aluminum,White,Black,Grey,Silver Grey
Restriction of Usage
l Not compatible with materials with grease or exudation.
l Unsuitable for the airproof location, because it is required to absorb moisture in air to cure.
l Unsuitable for the frosty or moist surface.
l Unsuitable for the continually flooding or entire-year moist places.
l Cannot be used on the unclean or unstable substrate.
l Cannot be used on the substrate surface under 6°C or above 40°C.
l Cannot be used on joint which bearing structural strength or places of physical damage.
Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
Safety
l Silicone sealant will release volatile compound so that it could be harm to health, therefore, please keep good and ventilate;
l Silicone sealant will not release any harmful substance and anything harm to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
Warranty
l As an ISO9001 certified company, we are committed to establish and implement the ISO9001 Quality Management System. We are recognized as manufacturer of silicone structural sealant for construction on August,2010.
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
Maintenance
l Generally there is no need to repair. If the seal joint is damaged, please remove the damaged silicone sealant, clean the surface of substrates, and fill up with silicone sealant.
l Hexin silicone sealants have good adhesion to cured sealant.
Purchase Channel and Price
l Users can buy Hexin silicone sealant from Guangzhou Hexin Industry Co.,Ltd and appointed regional agents to ensure the quality and realness
High quality weather resistance silicone sealant
For glass,curtain wall's non-structural sealing,various building doors&windows,metal structural engineering.
HX-8600 High quality weather resistance silicone sealant
Characteristics
l One component, RTV-1, Neutral Curing at room temperature silicone weatherproof sealant;
l Excellent weatherproofing performance, Excellent anti-ultraviolet proper;
l No need to prime coated, excellent joint to most building material;
l Excellent compatibility with other neutral silicone sealants
The Main Purpose
l Weatherproof seal for curtain wall such as glass, metal, concrete and stone, etc.
l Seal and joint with various glass windows and doors.
l Seal and joint roof light building.
Application Standard
GB/T 14683-2003; JC/T882-2001
Specification
l 300ml/cartridge; 24cartridge/ctn
l 590ml/sausage; 20sausage/ctn
l Color: Transparent,Aluminum,White,Black,Grey,Silver Grey
Restriction of Usage
l Not compatible with materials with grease or exudation;
l Unsuitable for the airproof location, because it is required to absorb moisture in air to cure;
l Unsuitable for the frosty or moist surface;
l Unsuitable for the continually flooding or entire-year moist places;
l Cannot be used on the unclean or unstable substrate;
l Cannot be used on the substrate surface under 6°C or above 40°C
l Cannot be used on joint which bearing structural strength or places of physical damage.
Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
Safety
l Silicone sealant will release volatile compound so that it could be harm to health, therefore, please keep good and ventilate;
l Silicone sealant will not release any harmful substance and anything harm to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
Warranty
l As an ISO9001 certified company, we are committed to establish and implement the ISO9001 Quality Management System. We are recognized as manufacturer of silicone structural sealant for construction on August,2010;
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
Maintenance
l Generally there is no need to repair. If the seal joint is damaged, please remove the damaged silicone sealant, clean the surface of substrates, and fill up with silicone sealant.
l Hexin silicone sealants have good adhesion to cured sealant.
Purchase Channel and Price
l Users can buy Hexin silicone sealant from Guangzhou Hexin Industry Co.,Ltd and appointed regional agents to ensure the quality and realness
HX-8600 High quality weather resistance silicone sealant
Characteristics
l One component, RTV-1, Neutral Curing at room temperature silicone weatherproof sealant;
l Excellent weatherproofing performance, Excellent anti-ultraviolet proper;
l No need to prime coated, excellent joint to most building material;
l Excellent compatibility with other neutral silicone sealants
The Main Purpose
l Weatherproof seal for curtain wall such as glass, metal, concrete and stone, etc.
l Seal and joint with various glass windows and doors.
l Seal and joint roof light building.
Application Standard
GB/T 14683-2003; JC/T882-2001
Specification
l 300ml/cartridge; 24cartridge/ctn
l 590ml/sausage; 20sausage/ctn
l Color: Transparent,Aluminum,White,Black,Grey,Silver Grey
Restriction of Usage
l Not compatible with materials with grease or exudation;
l Unsuitable for the airproof location, because it is required to absorb moisture in air to cure;
l Unsuitable for the frosty or moist surface;
l Unsuitable for the continually flooding or entire-year moist places;
l Cannot be used on the unclean or unstable substrate;
l Cannot be used on the substrate surface under 6°C or above 40°C
l Cannot be used on joint which bearing structural strength or places of physical damage.
Technology Service
l We supply integrate data, technical consultation and free compatibility test.
l Solving problem in the course of using timely
Safety
l Silicone sealant will release volatile compound so that it could be harm to health, therefore, please keep good and ventilate;
l Silicone sealant will not release any harmful substance and anything harm to health after cured;
l Keep uncured silicone sealant beyond children’s reach. If getting into eyes, wash off with running water and consult a doctor;
Warranty
l As an ISO9001 certified company, we are committed to establish and implement the ISO9001 Quality Management System. We are recognized as manufacturer of silicone structural sealant for construction on August,2010;
l We will sign the Quality Guarantee with customers after they buy our products and confirm the construction organization and engineering.
Maintenance
l Generally there is no need to repair. If the seal joint is damaged, please remove the damaged silicone sealant, clean the surface of substrates, and fill up with silicone sealant.
l Hexin silicone sealants have good adhesion to cured sealant.
Purchase Channel and Price
l Users can buy Hexin silicone sealant from Guangzhou Hexin Industry Co.,Ltd and appointed regional agents to ensure the quality and realness
High quility PU adhesive , PU glue for shoe
High quality general-purpose PU adhesive
excellent universal property
Type:
High quality general-purpose PU adhesive
Appearence:
Colorless transparent viscous liquid
Application and Characteristics:
General- purpose, non-yellowing, heat resistant, good initial bonding strength, bonding of PVC, PU, TPR, rubber, leather, etc. Suitable for hand made and production line.
adhesive, pu sealant,pu glue,polyurethane adhesive, PU adhesives
Strongly non-yellowing, strong initial bonding strength, excellent heat-resistance.Suitable for all kinds of material, especially the white material. viscosity:1600-1800cps heat-resistant:95°
HN-868HK is water clear,viscous liquid of brushing viscosity Polyurethane adhesive for footwear industry.
HN-868HK is formulated after a lot of application area research inputs from footwear manufacturers. The design of product is carefully done by selecting best available resins and solvents to ensure superior product performance.
APPLICATIONS:
HN-868HK has proved its versatility in footwear industry. The product offers excellent bonding strength on various substrates used in the footwear industry, offering total flexibility to the user industry.
Users favor HN-868HK with high preference for pasting various soling material to leather uppers.
Following substrates in footwear industry can be bonded with HN-868HK:
PVC Soles
PU Soles
TPR Soles
EVA Surfaces
Vulcanized resin/ micro cellular rubber
Welcome inquire on line or F:0086-757-85728852,MOB:+8613923129947
excellent universal property
Type:
High quality general-purpose PU adhesive
Appearence:
Colorless transparent viscous liquid
Application and Characteristics:
General- purpose, non-yellowing, heat resistant, good initial bonding strength, bonding of PVC, PU, TPR, rubber, leather, etc. Suitable for hand made and production line.
adhesive, pu sealant,pu glue,polyurethane adhesive, PU adhesives
Strongly non-yellowing, strong initial bonding strength, excellent heat-resistance.Suitable for all kinds of material, especially the white material. viscosity:1600-1800cps heat-resistant:95°
HN-868HK is water clear,viscous liquid of brushing viscosity Polyurethane adhesive for footwear industry.
HN-868HK is formulated after a lot of application area research inputs from footwear manufacturers. The design of product is carefully done by selecting best available resins and solvents to ensure superior product performance.
APPLICATIONS:
HN-868HK has proved its versatility in footwear industry. The product offers excellent bonding strength on various substrates used in the footwear industry, offering total flexibility to the user industry.
Users favor HN-868HK with high preference for pasting various soling material to leather uppers.
Following substrates in footwear industry can be bonded with HN-868HK:
PVC Soles
PU Soles
TPR Soles
EVA Surfaces
Vulcanized resin/ micro cellular rubber
Welcome inquire on line or F:0086-757-85728852,MOB:+8613923129947
High temperature 100% silicone Gasket maker
High temperature 100% silicone Gasket maker
Widely used in metal and other materials, for example: steel, iron, copper, gold,
High temperature 100% silicone Gasket maker
Clear RTV silicone gasket maker is single-component, non-slumping,
Acetate-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature.
Features:
1) Forms to any shapes instantly, and can cure fast
2) Resists cracking, shrinking and migration caused by thermal cycling
3) Works up to 260ºC
4) Mainly used for valve covers, water pumps, oil pans, axle covers, thermostats, transmission pans, timing chain covers, and oil pump flanges
5) Weight: 85g/pc
User's Guide:
1. Clean all surfaces thoroughly. Remove old gaskets and prepare flange surfaces. Dry and remove all oil and grease;
2. Remove the cap, puncture inner seal of the tube, screw on nozzle and cut the nozzle to desired size;
3. Apply continuous, uniform 1~4mm bead around perimeter of one surface. Completely surround all bolt holes;
4. Wait about 10 minutes for silicone to skin over. Then reassemble the parts.
5. Silicone dries to touch in 1 hour and allow 24 hours to fully cure and bond.
Widely used in metal and other materials, for example: steel, iron, copper, gold,
High temperature 100% silicone Gasket maker
Clear RTV silicone gasket maker is single-component, non-slumping,
Acetate-curing rubber paste that cures to a permanently flexible silicone rubber on exposure to atmospheric moisture at room temperature.
Features:
1) Forms to any shapes instantly, and can cure fast
2) Resists cracking, shrinking and migration caused by thermal cycling
3) Works up to 260ºC
4) Mainly used for valve covers, water pumps, oil pans, axle covers, thermostats, transmission pans, timing chain covers, and oil pump flanges
5) Weight: 85g/pc
User's Guide:
1. Clean all surfaces thoroughly. Remove old gaskets and prepare flange surfaces. Dry and remove all oil and grease;
2. Remove the cap, puncture inner seal of the tube, screw on nozzle and cut the nozzle to desired size;
3. Apply continuous, uniform 1~4mm bead around perimeter of one surface. Completely surround all bolt holes;
4. Wait about 10 minutes for silicone to skin over. Then reassemble the parts.
5. Silicone dries to touch in 1 hour and allow 24 hours to fully cure and bond.
High temperature Easy tore resist solder glue
1 Easy tore resist solder glue
2 Reach to 280 celsius degree
3 No residues
4 No corrosion
Easy tore resist solder glue
Product Introduction
Ausbond 120 high temperature tearable welding resist solder glue is composed of natural glue, which is a new type of product replacing traditional high temperature tape.It effectively avoid the inconvenience and detachment as well as the defects of preparation and cleaning work during pre-use and post-use.It can effectively help the user to improve the production efficient and product quality and provide reasonable and variable production work craft plan.
Product Features
1. The coating area pasted to circuit should be torn up with hand or tweezers lightly when it needs removing without residues.
2. The gold, copper and bronze won't be oxidized.
3. The parts won't take erosion.
4. It can avoid pollution in the process of assembling.
5. It can be brought down by microbiologic, which complies with requirement of environmental protection.
Product Application
It is widely applied to the products that need anti-welding, protection and hiding effectiveness temporally, such as wave peak welding and coating work craft.
1. Pasting on the circuit board that needs anti-welding in the process of wave peak welding; the surface of block circuit should be touched with coating.
2. It can be used for the welding of joint, golden finger, hole of screw, eye of hole and electronic parts.
3.The electronic products should protect sensitive components before conformal coating.
Process Used
1. Surface cleaning: clean the surface of the coated materials to remove rust, dust and grease.
2. Working: open the cover of bottle first and the top of cover should be cut for the use of pressing and coating or you can open the cover directly to use it by dipping the surface of product with brush.
3. Solidification: the coating is 2mm and can be dried within 2 hours at normal temperature or baked for 30 minutes at the temperature of 60 celsius degree.
Application features
1. This product should avoid surpassing 2 hours at the temperature of 94 celsius degree~120 celsius degree and avoid surpassing 1 hour at the temperature of120 celsius degree~149 celsius degree.
2. Don’t pour the glue liquid that has been poured out into the original package again, to avoid polluting the glue liquid.
3. Never kept in fridge or at high temperature; the light-proof container is suitable to use when keeping at the normal temperature.
4. Please store it in the place out reach of children.
5. This product contains slight smell that has little irritant for skin and eyes, in case of spattering into the eyes, please flush with lots of water immediately, and go to hospital if necessary; in case of contacting the skin, please flush with soap and lots of clean water.
6. For more safety notes about this product, please see Material Safety Data Sheet of Ausbond.
Package Specification
250ml/bottle;5L/barrel.20L/barrel
Storage and Transport
1. Store in the cool and dry place, with shelf life 12 months (25 celsius degree).
2. This product belongs to non-dangerous articles; please transport it as general articles.
3. For the product over storage life, please use it after confirming whether it is abnormal.
2 Reach to 280 celsius degree
3 No residues
4 No corrosion
Easy tore resist solder glue
Product Introduction
Ausbond 120 high temperature tearable welding resist solder glue is composed of natural glue, which is a new type of product replacing traditional high temperature tape.It effectively avoid the inconvenience and detachment as well as the defects of preparation and cleaning work during pre-use and post-use.It can effectively help the user to improve the production efficient and product quality and provide reasonable and variable production work craft plan.
Product Features
1. The coating area pasted to circuit should be torn up with hand or tweezers lightly when it needs removing without residues.
2. The gold, copper and bronze won't be oxidized.
3. The parts won't take erosion.
4. It can avoid pollution in the process of assembling.
5. It can be brought down by microbiologic, which complies with requirement of environmental protection.
Product Application
It is widely applied to the products that need anti-welding, protection and hiding effectiveness temporally, such as wave peak welding and coating work craft.
1. Pasting on the circuit board that needs anti-welding in the process of wave peak welding; the surface of block circuit should be touched with coating.
2. It can be used for the welding of joint, golden finger, hole of screw, eye of hole and electronic parts.
3.The electronic products should protect sensitive components before conformal coating.
Process Used
1. Surface cleaning: clean the surface of the coated materials to remove rust, dust and grease.
2. Working: open the cover of bottle first and the top of cover should be cut for the use of pressing and coating or you can open the cover directly to use it by dipping the surface of product with brush.
3. Solidification: the coating is 2mm and can be dried within 2 hours at normal temperature or baked for 30 minutes at the temperature of 60 celsius degree.
Application features
1. This product should avoid surpassing 2 hours at the temperature of 94 celsius degree~120 celsius degree and avoid surpassing 1 hour at the temperature of120 celsius degree~149 celsius degree.
2. Don’t pour the glue liquid that has been poured out into the original package again, to avoid polluting the glue liquid.
3. Never kept in fridge or at high temperature; the light-proof container is suitable to use when keeping at the normal temperature.
4. Please store it in the place out reach of children.
5. This product contains slight smell that has little irritant for skin and eyes, in case of spattering into the eyes, please flush with lots of water immediately, and go to hospital if necessary; in case of contacting the skin, please flush with soap and lots of clean water.
6. For more safety notes about this product, please see Material Safety Data Sheet of Ausbond.
Package Specification
250ml/bottle;5L/barrel.20L/barrel
Storage and Transport
1. Store in the cool and dry place, with shelf life 12 months (25 celsius degree).
2. This product belongs to non-dangerous articles; please transport it as general articles.
3. For the product over storage life, please use it after confirming whether it is abnormal.
High temperature RTV silicone sealant
High temperature RTV Silicone (Acetate 85gm red) Gasket Maker
It is resistance Tem from-80F to 650F(343 degree c)
High-Tem RTV Silicone ( Gasket Maker )
Color
:
Red, Grey, Black, Blue, Transparent, White
Main feature:
It can substitute any gasket instantly.
It is Ideal forming covers, value vocer, oil pans, intake manifolds, water pumps, dires secureiy as gasket.
Room temperature solidification,after curing,it resists cracking,shrinking and migration caused by thermal cycling.
Good resistance of water,oil,anti-freeze and transmission fluid.
It is resistance Tem from -80 F to 650 F ( 343 degree c ).
Packing:
15gm , 32gm, 50gm,71gm,85gm,100gm, 300ml tube with box or tube with blister card.
It is resistance Tem from-80F to 650F(343 degree c)
High-Tem RTV Silicone ( Gasket Maker )
Color
:
Red, Grey, Black, Blue, Transparent, White
Main feature:
It can substitute any gasket instantly.
It is Ideal forming covers, value vocer, oil pans, intake manifolds, water pumps, dires secureiy as gasket.
Room temperature solidification,after curing,it resists cracking,shrinking and migration caused by thermal cycling.
Good resistance of water,oil,anti-freeze and transmission fluid.
It is resistance Tem from -80 F to 650 F ( 343 degree c ).
Packing:
15gm , 32gm, 50gm,71gm,85gm,100gm, 300ml tube with box or tube with blister card.
High temperature adhesives
High temperature adhesives
1.good bonding effect.
2. room temperature curing.
3.anti-wind erosion
4.short hardening time
High temperature adhesives
Product Description:
High Temperature Adhesive(HTA)
HTA possesses the features of high consolidation strength, short hardening time, low porosity.
This product is light gray, thick flakes, was basic, combined with power.
Features:Has a good effect for bonding.
Room temperature curing.
Has an excellent ability of anti-wind erosion.
Product Applications:
A. aluminosilicate fiber bonding between.
B. aluminosilicate fiber and metal bonding equipment
C. aluminosilicate fiber bond and various kinds of refractory bricks
D. masonry firebrick
Note:
Pre-construction, need for adequate mixing so that uniformly. Construction should be sticky to remove surface dust, or metal oxide.
1.good bonding effect.
2. room temperature curing.
3.anti-wind erosion
4.short hardening time
High temperature adhesives
Product Description:
High Temperature Adhesive(HTA)
HTA possesses the features of high consolidation strength, short hardening time, low porosity.
This product is light gray, thick flakes, was basic, combined with power.
Features:Has a good effect for bonding.
Room temperature curing.
Has an excellent ability of anti-wind erosion.
Product Applications:
A. aluminosilicate fiber bonding between.
B. aluminosilicate fiber and metal bonding equipment
C. aluminosilicate fiber bond and various kinds of refractory bricks
D. masonry firebrick
Note:
Pre-construction, need for adequate mixing so that uniformly. Construction should be sticky to remove surface dust, or metal oxide.
202C Urea Formaldehyde Resin Powder
202C Urea Formaldehyde Resin Powder
Usage:Plywood/Particle Board / MDF/ HDF and so on.
1. Product Specialty:
Users can apply 202C UFR powder with variety of additives to satisfy their requirement. The
user can process 202C UFR Powder to various wood adhesives according to their actual
need. This powder is suitable for the cold pressing and hot pressing project. The outstanding
feature of 202C is the strong adaptability and flexible processing conditions. It could mix with
general kind of hardeners and could reach ideal bonding effect.
High bonding strength
Easy for use
Formaldehyde emission controlled under International standard
Both cold and hot solidification could reach ideal effect
Similar wood color, and do not pollute the wood
Excellent water resistance
Convenient for transportation
2. Application Areas
202C is suitable for the processing of plywood, particle board, MDF&HDF and the other
wood production which need to use cold setting technology. Below are mainly applications
for reference:
Various kind of wood composite boards
Gluing Plywood & Bentwood
Surface veneer for furniture and decorative boards
Engineered solid wood flooring
3. Performance Index
Item Unit Description
Appearance White Powder
Moisture Content % ≤1
202C
UFR Powder
Technical Information Sheet
Volatile Substance % 2.0
Free Formaldehyde Content (60% Solution) % 0.5
Molar Ratio (F/U) -- 1.55
Bulk Density Kg/m3 500+100
Curing Time (20) Depend on the Added Qty of Hardener
Shearing StrengthUnder Pressure after 20h Mpa >15
Shearing Strength of Water Resistance
Under Water after 24h
Mpa >11
Active Period after Mixture Depend on the Added Qty of Hardener
4. Mixture of Glue
a) Mixture Ratio(weight): UF Powder: Water=1: ≤0.6
b) Dissolution Method:
Put 2/3 of the total needed water into mixer, and then add UF powder in. Switch on the
mixer with speed of 50~150 rotations / minute, after glue powder being completely
dissolved, put the remained 1/3 water in mixer and churn for 3~5minutes until the glue
solution is completely mixed together again.
c) The user could add hardener into the mixed liquid glue according to actual
requirement, and control the active period of dissolved liquid glue.
5. Storage & Note:
1. Storage life: 1 years under temperature lower than 30.
2. The goods should be stored in a dry, ventilated location. Avoid direct sunshine and
moisture.
3. The package should be sealed again immediately once the pack has been opened to
avoid moisture.
4. Avoid contact with eyes. Once splashed into eyes, flushed out with plenty of clean
water. Consults doctor if necessary.
6. Package:
1. 3-ply paper bag with polyethylene liners.
2. 20kg/package.
Usage:Plywood/Particle Board / MDF/ HDF and so on.
1. Product Specialty:
Users can apply 202C UFR powder with variety of additives to satisfy their requirement. The
user can process 202C UFR Powder to various wood adhesives according to their actual
need. This powder is suitable for the cold pressing and hot pressing project. The outstanding
feature of 202C is the strong adaptability and flexible processing conditions. It could mix with
general kind of hardeners and could reach ideal bonding effect.
High bonding strength
Easy for use
Formaldehyde emission controlled under International standard
Both cold and hot solidification could reach ideal effect
Similar wood color, and do not pollute the wood
Excellent water resistance
Convenient for transportation
2. Application Areas
202C is suitable for the processing of plywood, particle board, MDF&HDF and the other
wood production which need to use cold setting technology. Below are mainly applications
for reference:
Various kind of wood composite boards
Gluing Plywood & Bentwood
Surface veneer for furniture and decorative boards
Engineered solid wood flooring
3. Performance Index
Item Unit Description
Appearance White Powder
Moisture Content % ≤1
202C
UFR Powder
Technical Information Sheet
Volatile Substance % 2.0
Free Formaldehyde Content (60% Solution) % 0.5
Molar Ratio (F/U) -- 1.55
Bulk Density Kg/m3 500+100
Curing Time (20) Depend on the Added Qty of Hardener
Shearing StrengthUnder Pressure after 20h Mpa >15
Shearing Strength of Water Resistance
Under Water after 24h
Mpa >11
Active Period after Mixture Depend on the Added Qty of Hardener
4. Mixture of Glue
a) Mixture Ratio(weight): UF Powder: Water=1: ≤0.6
b) Dissolution Method:
Put 2/3 of the total needed water into mixer, and then add UF powder in. Switch on the
mixer with speed of 50~150 rotations / minute, after glue powder being completely
dissolved, put the remained 1/3 water in mixer and churn for 3~5minutes until the glue
solution is completely mixed together again.
c) The user could add hardener into the mixed liquid glue according to actual
requirement, and control the active period of dissolved liquid glue.
5. Storage & Note:
1. Storage life: 1 years under temperature lower than 30.
2. The goods should be stored in a dry, ventilated location. Avoid direct sunshine and
moisture.
3. The package should be sealed again immediately once the pack has been opened to
avoid moisture.
4. Avoid contact with eyes. Once splashed into eyes, flushed out with plenty of clean
water. Consults doctor if necessary.
6. Package:
1. 3-ply paper bag with polyethylene liners.
2. 20kg/package.
High-concentration colloidal silica
High-concentration colloidal silica( silicon dioxide, silica sol)Particle size 8-20(nm),low impurity, high diaphaneity, etc.
High-concentration colloidal silica( silicon dioxide, silica sol)
GS-40, GS-35 are two types of high-concentration colloidal silica. Their technical standards are listed below
Designation
Standard
GS-40
GS-35
Appearance
Slight milky transparent to translucent
SiO
2
(wt%)
40±1%
35±1%
Na
2
O (wt%)
≤0.7%
≤0.5%
PH (20°C)
9.5-10.5
9.0-11.0
Density (20°C,g/cm
3
)
1.280-1.295
1.24-1.25
Viscosity(25°C,mPaS)
10-35
≤20
Particle size (nm)
10-15
8-20
Packing & Storage
Colloidal silica is packed in 25kg,250kg or 1000kg plastic drums.
Store the colloidal silica at a temperature between 0 and 50, avoid exposure to the air, and insulate it from the sun.
Wash the empty drums as quickly as possible to avoid SiO
2
crystalline deposits.
If you want to remove the deposition from empty drums, use a 10-percent NaOH solution at 50~60.
High-concentration colloidal silica( silicon dioxide, silica sol)
GS-40, GS-35 are two types of high-concentration colloidal silica. Their technical standards are listed below
Designation
Standard
GS-40
GS-35
Appearance
Slight milky transparent to translucent
SiO
2
(wt%)
40±1%
35±1%
Na
2
O (wt%)
≤0.7%
≤0.5%
PH (20°C)
9.5-10.5
9.0-11.0
Density (20°C,g/cm
3
)
1.280-1.295
1.24-1.25
Viscosity(25°C,mPaS)
10-35
≤20
Particle size (nm)
10-15
8-20
Packing & Storage
Colloidal silica is packed in 25kg,250kg or 1000kg plastic drums.
Store the colloidal silica at a temperature between 0 and 50, avoid exposure to the air, and insulate it from the sun.
Wash the empty drums as quickly as possible to avoid SiO
2
crystalline deposits.
If you want to remove the deposition from empty drums, use a 10-percent NaOH solution at 50~60.
High-end rubber adhesion promotor and fortifier DA101
It is used in high-end rubber, especially tires. DA101 has good chemical reactivity, low tire calorific value, and low hydroge
High-end rubber adhesion promotor and fortifier DA101
This is kind of Dicyclopentadiene (DCPD) resins, which is used for applications requiring high surface finish. Physical properties are similar to the ortho resins, but much better.
In lipid solvent, it has a good compatibility with Double epoxy resin
It can serve as in paint, in order to increase the final finishes of paints, the adhesiveness of paint films and the hardness, Resistance to acid and alkaline
Appearance (granule)..
Soft point(95-125°)
Color(6#)
Insoluble(0.03)
Acid Value(0.5max)
It is used in high-end rubber, especially tires. DA101 has good chemical reactivity, low tire calorific value, and low hydrogen. So it's playing a very good role as adhesion promotor and fortifier..
Puyang Zhongde Petroleum Resins Co., LTD,
Fax: (86)393-5398995
Tel: (86)393-8999588
High-end rubber adhesion promotor and fortifier DA101
This is kind of Dicyclopentadiene (DCPD) resins, which is used for applications requiring high surface finish. Physical properties are similar to the ortho resins, but much better.
In lipid solvent, it has a good compatibility with Double epoxy resin
It can serve as in paint, in order to increase the final finishes of paints, the adhesiveness of paint films and the hardness, Resistance to acid and alkaline
Appearance (granule)..
Soft point(95-125°)
Color(6#)
Insoluble(0.03)
Acid Value(0.5max)
It is used in high-end rubber, especially tires. DA101 has good chemical reactivity, low tire calorific value, and low hydrogen. So it's playing a very good role as adhesion promotor and fortifier..
Puyang Zhongde Petroleum Resins Co., LTD,
Fax: (86)393-5398995
Tel: (86)393-8999588
High-grade Aluminum Plastic Panel curtain wall sealant(JH-3680)
1)manufacturer
2)suitable for weather sealing in aluminum-plastic composite plate curtain wall
3)excellant performance
QIAN LI MA® JH-3680 Silicone Weather Resistance Sealant
1.Characteristics:
JH-3680 Belongs to RTV-1, expediently application between 4-40c alcoxy curing system,expediently application between 5-50c to oxmie curing system.
Neutral curing,non-corrosive to glass,coated glass,concrete,marble,metal(not including oxime curing system)and most kinds of plastic etc
Quick speed of curing,excellent adhesion,middle modulus,exellent movement capability
Excellent resistance to weather,the service life is over 50 years in the condition of general weather
Excellent resistance to low and high temperature change. Little changes of performance at -40~150°C;
Excellent adhesive to aluminum panel,aluminum plastic panel and other building materials
Good compatibility with other neutral silicone sealants;
Good compatibility with other neutral silicone sealants
2.Purpose:
For weather sealing in all type alum,curtain wall joints and aluminum-plastics composite plate curtain wall joints
For weather sealing in metal,plastic and concrete
Sealing in roof joints of constructions
Many other building&Industrial uses
3.Typical Technology Data:
Performance
Standard JC/T882-2001
Measured Value
Testing method
Alcoxy
Oxime
Slumpability (mm)
≤3
0
1
GB/T 13477
Extrusion (S)
≥80
130.9
145
Tack-Free Time (min)
≤180
70
90
Hardness (HsA)
/
51
46
GB/T 531
Loss of Heating %
≤10
3.3
3.8
ASTMC 792
Tensile strength in adhesion(Mpa)
>0.4(high modulus)
1.0
0.83
GB/T 13477
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Movement Capability
+20
+20
+20
ASTMC719
Elongation at ultimate strength %
/
250
260
GB/T 13477
Stability
Store for 12 months at –20~27°C in cool, dry place after date of manufacture
4.Application Standard:
Standard JC/T 882-2001 Curtain wall sealing silicone sealant
5.Restriction of Usage:
Can't be used as structural sealant
Unsuitable for the surface of all kinds of material that can effuse grease,plasticizer or solvent
Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
Unsuitable for the frosty or moist surface;
Unsuitable for the continually soggy or moist place;
Can’t be used the product of alcoxy ,if the temperature is below 4°C or above 40°C on the surface of the material.Can't be used the product of oxime,if the temperature is below 5°C or above 50°C on the surface of the material
6.Color and Package:
Color:Back,Gray,White or other color on request to JH-3680
Package: 310ml Cartridge net 300ml, 590ml ham bag
7. Joint Design and Working Procedure:
Please refer to Section “The Technology Instruction of Jianhua Silicone structural sealant”
8. Technical Service
Offer the integral technical data of the products.
9. Others:
We passed the ISO9001 international quality system certification. And we control the quality according to the ISO9001 System strictly.
Insurance agent: PICC
2)suitable for weather sealing in aluminum-plastic composite plate curtain wall
3)excellant performance
QIAN LI MA® JH-3680 Silicone Weather Resistance Sealant
1.Characteristics:
JH-3680 Belongs to RTV-1, expediently application between 4-40c alcoxy curing system,expediently application between 5-50c to oxmie curing system.
Neutral curing,non-corrosive to glass,coated glass,concrete,marble,metal(not including oxime curing system)and most kinds of plastic etc
Quick speed of curing,excellent adhesion,middle modulus,exellent movement capability
Excellent resistance to weather,the service life is over 50 years in the condition of general weather
Excellent resistance to low and high temperature change. Little changes of performance at -40~150°C;
Excellent adhesive to aluminum panel,aluminum plastic panel and other building materials
Good compatibility with other neutral silicone sealants;
Good compatibility with other neutral silicone sealants
2.Purpose:
For weather sealing in all type alum,curtain wall joints and aluminum-plastics composite plate curtain wall joints
For weather sealing in metal,plastic and concrete
Sealing in roof joints of constructions
Many other building&Industrial uses
3.Typical Technology Data:
Performance
Standard JC/T882-2001
Measured Value
Testing method
Alcoxy
Oxime
Slumpability (mm)
≤3
0
1
GB/T 13477
Extrusion (S)
≥80
130.9
145
Tack-Free Time (min)
≤180
70
90
Hardness (HsA)
/
51
46
GB/T 531
Loss of Heating %
≤10
3.3
3.8
ASTMC 792
Tensile strength in adhesion(Mpa)
>0.4(high modulus)
1.0
0.83
GB/T 13477
Permanent set adhesion
Non destroyed
Non destroyed
Non destroyed
Movement Capability
+20
+20
+20
ASTMC719
Elongation at ultimate strength %
/
250
260
GB/T 13477
Stability
Store for 12 months at –20~27°C in cool, dry place after date of manufacture
4.Application Standard:
Standard JC/T 882-2001 Curtain wall sealing silicone sealant
5.Restriction of Usage:
Can't be used as structural sealant
Unsuitable for the surface of all kinds of material that can effuse grease,plasticizer or solvent
Unsuitable for the airproof location, because it is required to absorb moisture in air to cure for the sealant;
Unsuitable for the frosty or moist surface;
Unsuitable for the continually soggy or moist place;
Can’t be used the product of alcoxy ,if the temperature is below 4°C or above 40°C on the surface of the material.Can't be used the product of oxime,if the temperature is below 5°C or above 50°C on the surface of the material
6.Color and Package:
Color:Back,Gray,White or other color on request to JH-3680
Package: 310ml Cartridge net 300ml, 590ml ham bag
7. Joint Design and Working Procedure:
Please refer to Section “The Technology Instruction of Jianhua Silicone structural sealant”
8. Technical Service
Offer the integral technical data of the products.
9. Others:
We passed the ISO9001 international quality system certification. And we control the quality according to the ISO9001 System strictly.
Insurance agent: PICC
High-performance Silicone Weatherproof Sealant
High-performance Silicone Weatherproof Sealant
1.single component
2.neutral curing
3.high modulus
4.long lifetime
Features:
1. Single component, neutral curing, high modulus.
2. Good weatherproof performance, long lifetime.
3. Aging resistance, ultraviolet radiation proof.
4. Has no corrosive for metal and coated glass.
5. Need not primary coat in normal condition.
6. Has good adhesion for most building materials.
Application Range
:
1. Used for glass curtain wall weathering sealing.
2. Aluminium plate curtain wall weathering sealing.
3. Concrete, plastic and metal joint sealing.
4. Roof joint sealing.
5. Many other purposes.
Colors:
White,Black
Package:
Inner packing:
300ml/plastic cartridge
590ml
Outer packing:
24/ctn
20/ctn
1.single component
2.neutral curing
3.high modulus
4.long lifetime
Features:
1. Single component, neutral curing, high modulus.
2. Good weatherproof performance, long lifetime.
3. Aging resistance, ultraviolet radiation proof.
4. Has no corrosive for metal and coated glass.
5. Need not primary coat in normal condition.
6. Has good adhesion for most building materials.
Application Range
:
1. Used for glass curtain wall weathering sealing.
2. Aluminium plate curtain wall weathering sealing.
3. Concrete, plastic and metal joint sealing.
4. Roof joint sealing.
5. Many other purposes.
Colors:
White,Black
Package:
Inner packing:
300ml/plastic cartridge
590ml
Outer packing:
24/ctn
20/ctn
High-temperature Silicone Sealant
1.Single component
2.acid curing
3.high modulus
4.high temperature proof
Product description:
Single component, acid curing, and high modulus, high temperature proof, high adhesion, long duration. Mainly used for adhering metal (cylinder cushion in vehicle), glass, ceramics, ceramic tile, leather, rubber, plastic, etc.
Construction requirement:
The construction surface must be clean, dry, and cannot be used for structural assembly. Cannot be used for the surface easily penetrating oil and plasticizer, and for the place that has not been sulfurized or partially sulfurized, and cannot be used for the place that might be contacted with the marble, granite and other alkaline matter.
Slump
/ mm
≤ 1
Extrudability /ml/min
≥ 80
Tack-free time
/ min
≤ 180
Weight loss on heating
/%
≤ 10
Elastic recovery ratio
/%
≥ 80
Tensile modulus / Mpa (standard conditions)
> 0.4
Tensile properties at maintained extension
No damage
Cohesiveness after UV radiation
No damage
Cohesiveness after hot pressing-cold extending
No damage
Definite elongation cohesiveness after emergence
No damage
2.acid curing
3.high modulus
4.high temperature proof
Product description:
Single component, acid curing, and high modulus, high temperature proof, high adhesion, long duration. Mainly used for adhering metal (cylinder cushion in vehicle), glass, ceramics, ceramic tile, leather, rubber, plastic, etc.
Construction requirement:
The construction surface must be clean, dry, and cannot be used for structural assembly. Cannot be used for the surface easily penetrating oil and plasticizer, and for the place that has not been sulfurized or partially sulfurized, and cannot be used for the place that might be contacted with the marble, granite and other alkaline matter.
Slump
/ mm
≤ 1
Extrudability /ml/min
≥ 80
Tack-free time
/ min
≤ 180
Weight loss on heating
/%
≤ 10
Elastic recovery ratio
/%
≥ 80
Tensile modulus / Mpa (standard conditions)
> 0.4
Tensile properties at maintained extension
No damage
Cohesiveness after UV radiation
No damage
Cohesiveness after hot pressing-cold extending
No damage
Definite elongation cohesiveness after emergence
No damage
Hitecmen Polyurethane Structural Sealant
Hitecmen PU602C is one component moisture curable polyurethane structural sealant developed by our doctors and produced under IS
Hitecmen PU602C is one component moisture curable polyurethane structural sealant
developed by our doctors and produced under ISO9001 and TS16949 quality system
control. It is a kind of environment-friendly one component fast curable polyurethane
sealant/adhesive with long supporting performance. It is widely used for the
bonding and sealing of glass, metal, plastic, stone, ceramic and rubber, etc.
Hitecmen PU602C is one component moisture curable polyurethane structural sealant
developed by our doctors and produced under ISO9001 and TS16949 quality system
control. It is a kind of environment-friendly one component fast curable polyurethane
sealant/adhesive with long supporting performance. It is widely used for the
bonding and sealing of glass, metal, plastic, stone, ceramic and rubber, etc.
Hongying 2000 silicone Weathering Sealant
general purpose neutral sealant
weather and aging resistance.
different colors available.
for windows and glass
HONGYING-2300 HIGH-GRADE SILICONE WEATHERING SEALANT
PRODUCT FEATURES
*One component, neutral, room temperature curing, high modulus.
*Ideal for expansion, connection, perimeter and other movement joints.
*Excellent weather ability, virtually unaffected by sunlight, rain, snow, ozone.
*Excellent unprimed adhesion to a wide variety of construction
*9-month shelf life
* Excellent durability and recovery after repeated extension and compression
*100% high quality raw materilas.
*General purpose neutral silicone sealant.
MAIN APPLICATION
Bonding and sealing for non-structural assembling of glass, aluminum plastic plate, concrete, aluminum products, tile, ceramic products and other building material, as well as other purposes.
TYPICAL TECHNOLOGICAL DATE
No.
Performance
Standard
Measured Value
Single Evaluation
1
Appearance
Fine and uniform ointment, it shall not have bubble, sufface coagulation or gel
Conform to standard
Qualified
2
Slumpability
(mm)
Vertical
≤3
0
Qualified
Horizontal
Non distorted
Non distorted
Qualified
3
Tack-Free Time (h)
≤3
0.8
Qualified
4
Extrusion (mL/min)
≥80
762
Qualified
5
Tensile Modulus
(MPa)
23°C
>0.4
0.5
Qualified
-20°C
>0.6
/
Qualified
6
Tensile properties at maintained extension
Non destroyed
Non destroyed
Qualified
OPERATIVE NORM
B GF 20HM GB/T14683-2003
weather and aging resistance.
different colors available.
for windows and glass
HONGYING-2300 HIGH-GRADE SILICONE WEATHERING SEALANT
PRODUCT FEATURES
*One component, neutral, room temperature curing, high modulus.
*Ideal for expansion, connection, perimeter and other movement joints.
*Excellent weather ability, virtually unaffected by sunlight, rain, snow, ozone.
*Excellent unprimed adhesion to a wide variety of construction
*9-month shelf life
* Excellent durability and recovery after repeated extension and compression
*100% high quality raw materilas.
*General purpose neutral silicone sealant.
MAIN APPLICATION
Bonding and sealing for non-structural assembling of glass, aluminum plastic plate, concrete, aluminum products, tile, ceramic products and other building material, as well as other purposes.
TYPICAL TECHNOLOGICAL DATE
No.
Performance
Standard
Measured Value
Single Evaluation
1
Appearance
Fine and uniform ointment, it shall not have bubble, sufface coagulation or gel
Conform to standard
Qualified
2
Slumpability
(mm)
Vertical
≤3
0
Qualified
Horizontal
Non distorted
Non distorted
Qualified
3
Tack-Free Time (h)
≤3
0.8
Qualified
4
Extrusion (mL/min)
≥80
762
Qualified
5
Tensile Modulus
(MPa)
23°C
>0.4
0.5
Qualified
-20°C
>0.6
/
Qualified
6
Tensile properties at maintained extension
Non destroyed
Non destroyed
Qualified
OPERATIVE NORM
B GF 20HM GB/T14683-2003
Subscribe to:
Posts (Atom)