2013 Epoxy adhesive is a low viscosity epoxy especially developed for production of
Articles and mould cast.The hardener is low
Epoxy Resin 2013A/B
DESCRIPTION:
2013 Epoxy adhesive is a low viscosity epoxy especially developed for production of
Articles and mould cast.The hardener is low contractility, high physical dimension stable. Compatibility with fibers and caulking material. A wide range use for mould cast, manufacture composite material and encapsulation of transformers and coils for the electronic and electrical industries
SPECIFICATION:
PARTS
Appearance
Viscosity at 25 0c
(mPa s)
Density at 25 0c
g/cm3
Shelf life
2013A
Buff, Transparent.
Liquid
3500-3800
1.53
12 months
2013B
Colorlessness
Transparent.
Liquid
100-150
0.92
12 months
Ratio for weight:
AB=100:25
Curing Time:
6-8 hours at 25
2 hours at 35
Complete Data sheet:
Compressive strength: 70-75 N/mm2
Tensile strength: 38.4 Mpa
Shore hardness: 80-85 ShoreD
Flexural Strength: 55-68
N/mm2
Distortion Temperature: 80
Impact toughness: 0.62 KJ/m2
PRECAUTIONS:
High atmospheric humidity or drops in temperature around dew point may result in condensation on the uncured film causing changes in the film surface as a result of hydration. This effect may cause loss of intercoat adhesion. In these conditions good adhesion may be obtained
by re-roughening the surface.
IMPORTANT NOTE:
The specification listed above is given to the best of our knowledge, however, it is given without any warranty expressed or implied. The specification is subject to change without notice. Consult QUALITY CONTROL REPORT available for each Batch for actual results.
Sunday, September 18, 2011
Epoxy adhesive
1)epoxy adhesive
2)top quality
3)competitive price and prompt delivery
4)professional service
5)certification: MSDS
Epoxy adhesive combine exceptional strength and durability. Bonds trim and ornaments.
Resistant to gasoline, anti-freeze and most solvents.
Item Name
Epoxy Adhesive; AB glue
Item NO.
AY-AB
Application
Great for household use
Specification
125g;250g;500g;750g;1KG and so on
Package
24sets/carton 48sets/carton and so on
Measurement
It's up to package
OEM
Available
Appearance
transparent; light yellow and so on
Shelf life
12 months
Certification
SGS; MSDS
2)top quality
3)competitive price and prompt delivery
4)professional service
5)certification: MSDS
Epoxy adhesive combine exceptional strength and durability. Bonds trim and ornaments.
Resistant to gasoline, anti-freeze and most solvents.
Item Name
Epoxy Adhesive; AB glue
Item NO.
AY-AB
Application
Great for household use
Specification
125g;250g;500g;750g;1KG and so on
Package
24sets/carton 48sets/carton and so on
Measurement
It's up to package
OEM
Available
Appearance
transparent; light yellow and so on
Shelf life
12 months
Certification
SGS; MSDS
Epoxy adhesive
1)epoxy adhesive
2)top quality
3)competive price and prompt delivery
4)professional service
5)certification: MSDS.
Epoxy adhesive combine exceptional strength and durability. Bonds trim and ornaments.
Resistant to gasoline, anti-freeze and most solvents.
Item Name
EPOXY GLUE
Item No.
AY-27
Application
For repair iron, ceramics, equipment
Specification
8ml/set 1set/card
Packing
144cards/carton
Measurement
48*30*49
OEM
Available
Appearance
Liquid, clear, 5-10minutes
Shelf life
12 months
Certification
MSDS
Usage:
Remove the plastic cap from in between the two tubes. Squeeze equal amounts from both tubes onto a clean surface and mix thoroughly until the color is uniform.
Storage:
Keep away from reach of children
Keep away from direct sunlight
Store in cool and dry place
More details:
2)top quality
3)competive price and prompt delivery
4)professional service
5)certification: MSDS.
Epoxy adhesive combine exceptional strength and durability. Bonds trim and ornaments.
Resistant to gasoline, anti-freeze and most solvents.
Item Name
EPOXY GLUE
Item No.
AY-27
Application
For repair iron, ceramics, equipment
Specification
8ml/set 1set/card
Packing
144cards/carton
Measurement
48*30*49
OEM
Available
Appearance
Liquid, clear, 5-10minutes
Shelf life
12 months
Certification
MSDS
Usage:
Remove the plastic cap from in between the two tubes. Squeeze equal amounts from both tubes onto a clean surface and mix thoroughly until the color is uniform.
Storage:
Keep away from reach of children
Keep away from direct sunlight
Store in cool and dry place
More details:
Epoxy anchor
JG701 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.Styrene Free
JG701
Fast setting Adhesive for Chemical Anchoring
Description
JG701 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG701 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
: JG701
variant
: 360ml 5:1 dual action side by side cartridge
designation
: medium to heavy duty
material
: epoxy acrylate, styrene free
finish
: grey on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns. Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG701 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
10~30 mins
4hours
0°C~+10°C
8~15 mins
70-120 mins
+10°C~+25°C
5~10 mins
40-70 mins
+25°C~+40°C
3~5mins
25-40 mins
>40°C
<2mins
20mins
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. JG701 can be cleaned with only mechanical abrasion after hardening.
Packaging
360 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children. For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience. YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
This technical data sheet is valid until the new edition is published and makes old editions invalid.
JG701
Fast setting Adhesive for Chemical Anchoring
Description
JG701 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG701 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
: JG701
variant
: 360ml 5:1 dual action side by side cartridge
designation
: medium to heavy duty
material
: epoxy acrylate, styrene free
finish
: grey on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns. Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG701 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
10~30 mins
4hours
0°C~+10°C
8~15 mins
70-120 mins
+10°C~+25°C
5~10 mins
40-70 mins
+25°C~+40°C
3~5mins
25-40 mins
>40°C
<2mins
20mins
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. JG701 can be cleaned with only mechanical abrasion after hardening.
Packaging
360 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children. For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience. YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
This technical data sheet is valid until the new edition is published and makes old editions invalid.
Epoxy cartridge
JG702 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.Styrene Free
JG702
Fast setting Adhesive for Chemical Anchoring
Description
JG701 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG702 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
: JG702
variant
: 345ml 10:1 dual action side by side cartridge
designation
: medium to heavy duty
material
: epoxy acrylate, styrene free
finish
: grey on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns. Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG702 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
10~30 mins
4hours
0°C~+10°C
8~15 mins
70-120 mins
+10°C~+25°C
5~10 mins
40-70 mins
+25°C~+40°C
3~5mins
25-40 mins
>40°C
<2mins
20mins
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. JG702 can be cleaned with only mechanical abrasion after hardening.
Packaging
345 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children. For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience. YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
This technical data sheet is valid until the new edition is published and makes old editions invalid.
JG702
Fast setting Adhesive for Chemical Anchoring
Description
JG701 is Epoxyacrylate based, fas setting Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG702 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
: JG702
variant
: 345ml 10:1 dual action side by side cartridge
designation
: medium to heavy duty
material
: epoxy acrylate, styrene free
finish
: grey on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns. Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG702 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
10~30 mins
4hours
0°C~+10°C
8~15 mins
70-120 mins
+10°C~+25°C
5~10 mins
40-70 mins
+25°C~+40°C
3~5mins
25-40 mins
>40°C
<2mins
20mins
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. JG702 can be cleaned with only mechanical abrasion after hardening.
Packaging
345 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children. For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience. YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
This technical data sheet is valid until the new edition is published and makes old editions invalid.
Epoxy cartridge
JG400 is pure Epoxy based, Heavy duty-Hi load Adhesive for chemical anchoring in cartridge packaging.
JG400
Heavy duty-Hi load Adhesive for Chemical Anchoring
Description
JG400 is pure Epoxy based, Heavy duty-Hi load Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG400 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
:JG400
variant
: 400ml 3:1 dual action side by side cartridge
designation
: heavy duty - hi load
material
: pure epoxy ,styrene free
finish
: gray on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns.Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG400 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. YUANDA® JG400 can be cleaned with only mechanical abrasion after hardening.
Packaging
400 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children.For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience.YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
2~8hours
96~150hours
0°C~+10°C
1~2hours
48~96hours
+10°C~+25°C
30~50mins
24~48hours
+25°C~+40°C
20~30mins
7~24hours
>40°C
12mins
7 hours
JG400
Heavy duty-Hi load Adhesive for Chemical Anchoring
Description
JG400 is pure Epoxy based, Heavy duty-Hi load Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG400 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product
:JG400
variant
: 400ml 3:1 dual action side by side cartridge
designation
: heavy duty - hi load
material
: pure epoxy ,styrene free
finish
: gray on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns.Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG400 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Watchpoints
• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.
• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.
Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. YUANDA® JG400 can be cleaned with only mechanical abrasion after hardening.
Packaging
400 ml cartridge,40 Pcs/carton
Storage
Store in original container in cool (+5oC - +25oC) and dry indoor conditions.
Shelf life
12 months under proper storage conditions after production date.
Health and Safety
It is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children.For further information Material Safety Data Sheets should be read.
Disclaimer
This information and all further technical advice are based on our present knowledge and experience.YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
Cure Schedule
Base Material Temperature(°C)
Gelling time
Curing time
-10°C~0°C
2~8hours
96~150hours
0°C~+10°C
1~2hours
48~96hours
+10°C~+25°C
30~50mins
24~48hours
+25°C~+40°C
20~30mins
7~24hours
>40°C
12mins
7 hours
Epoxy construction chemical anchor
Construction use planting bar adhesives, epoxy adhesives, anchoring system,injective adhesive, chemical anchor
XQ-601 Injection Adhesives are compound of modified epoxy resin and nano materials, double component packed. The advantage on plating bar anchoring has been proved by many construction projects,
Features:
• Modified epoxy resin, styrene free, safe and non-toxic;
• High strength and reinforcement, good toughness, similar with pre-cemented;
• Good resistance against aging and heat, no creep under normal temperature;
• Low sensitivity with humidity, steady performance under moist condition;
XQ-601 Injection Adhesives are compound of modified epoxy resin and nano materials, double component packed. The advantage on plating bar anchoring has been proved by many construction projects,
Features:
• Modified epoxy resin, styrene free, safe and non-toxic;
• High strength and reinforcement, good toughness, similar with pre-cemented;
• Good resistance against aging and heat, no creep under normal temperature;
• Low sensitivity with humidity, steady performance under moist condition;
Subscribe to:
Posts (Atom)